Agar, Salih; Tosun, Nihat; Mahmat, Aybars

This study focused on determining the effects of the cooling condition in the conventional and ultrasonic-assisted turning of AISI 52100 steel. AISI 52100 steel has been widely used in the bearing, mold, and automotive industries because of its superior wear resistance and mechanical properties. However, its high wear resistance caused poor machinability in conventional machining methods. Low surface quality, rapid tool wear, high cutting temperature, and high cutting force are the main difficulties in the conventional machining of AISI 52100 steel. On the other hand, ultrasonic-assisted machining has become widely used in the past decades for the machining of materials that have low machinability in conventional methods. Conventional turning and ultrasonic-assisted turning were selected as machining methods. Ultrasonic-assisted turning experiments were conducted under 20 and 30 kHz vibration frequencies. Cubic Boron Nitride (CBN) cutting tools were used in machining experiments. In machining operations 50, 100, and 150 m/min cutting speeds were selected, and feed rate (0.1 mm/rev) and depth of cut (0.5 mm) were kept constant in experiments. Minimum quantity lubrication technique which used 1% Al2O3 nanoparticle additives cutting fluid and dry cooling methods were used. CBN insert was used as a cutting tool. The effects of cutting speed, cutting method, and cooling condition on surface quality, cutting force, cutting zone temperature, and cutting tool wear were studied experimentally. Analysis of Variance (ANOVA) was carried out to determine the significance of the effects of input variables on process outputs. As a result of this study, it is determined that combined UAT and nanoMQL have significant effects on the process outputs.

AtıfScopus3·WoS3·OpenAlex3

İncele

Tosun, Nihat; Rasul, Sleman Yahya; Mahmat, Aybars; Tosun, Gul

During the machining of aluminum alloys, the adhesion of chips to the tool affects the performance characteristics. Today, different cooling systems are used to eliminate these negativities. In this study, the effects of end milling using HSS and carbide cutting tools of 6061-T6 aluminum alloy on surface roughness, chip thickness ratio and tool wear were examined using different cooling techniques (dry, minimum quantity lubrication (MQL) and nanocutting fluid). Different cutting speeds (180, 200, 220 m/min) and different feed rates (0.05, 0.06, 0.07 mm/rev) were used in the experiments. According to experimental findings, tool wear and surface roughness decreased at low cutting speed and feed rate by using nanocutting fluid with carbide cutting tools. It has been observed that the chip thickness ratio increases with high cutting speeds using nanocutting fluid and decreases with dry machining and high feed rates. The best milling performance of the aluminum alloy was achieved in experiments using carbide cutting tools and nanocutting fluid.

AtıfScopus4·WoS4·OpenAlex4

İncele

Mahmat, Aybars; Tosun, Nihat; AǦar, Salih

This study aims to investigate experimentally and analytically the effects of different machining parameters such as cooling methods and cutting tool materials on surface roughness and chip thickness ratio for milling of AA7075-T6 aluminum alloy. The carbide and high-speed steel (HSS) end mills were used as cutting tools and the conventional, vapor, and compressed air were used as cooling methods in the experiments. The experiment conditions for compressed air at the cutting zone were 6 bar pressure and 30 m/s speed flow rate. A mixture of boron oil and water (1/20 mixture ratio) was used as cutting fluid in conventional cooling. The study was carried out using three levels of feed rates (20, 40, 80 mm/min), rotational speeds (780, 1330, 2440 rpm), and a constant 2 mm deep cut. As a result of the experiments, the surface roughness values increased with the increasing levels of feed rate. Besides surface roughness values decreased with increasing levels of the rotational speed. In addition, a better surface quality was obtained in milling processes by using carbide cutting tools compared to HSS tools. It was concluded that the most important parameter affecting the surface roughness and chip thickness ratio is feed rate and the rotational speed, respectively. Better surface roughness and chip thickness ratio were obtained from the vapor processing than the conventional and compressed air.

AtıfScopus2·WoS1

İncele