Sürdürülebilir Kalkınma Amaçları

• 3
• 2

• MakaleAçık Erişim2023/r/munzur/6447
  Cu/Zn Oksit İkili Katalizörü Üretmek Amacıyla Malahit Cevherinin NH3/NH4NO3 Liçinde Optimum pH ve NH3 Derişiminin Yanıt Yüzey Yöntemiyle Belirlenmesi

  Demirkiran, Nizamettin; Tanaydın, Zümra Bakıcı; Baysar, Ahmet

  Bu çalışmada, bir hidrosikarbonat minerali olan malahit ve bir karbonatlı mineral olan simitsonit içeren bakır cevherinin hidrometalurjik yöntemle işlenmesi neticesinde Cu/Zn oksit ikili katalizörü üretilmiştir. Cevherden maksimum oranda bakır ve minimum oranda çinkonun liç çözeltisine geçmesini sağlayacak ancak cevherde bulunan diğer metallerin çözünmesini engelleyecek pH ve çözücü derişiminin optimum değerleri yanıt yüzey yöntemi ile belirlenmiştir. Yanıt yüzey yönteminde elde edilen deneysel bulgulara çoklu regresyon analizi yapılarak bakır ve çinko liç verimleri ile bağımsız değişkenler arasındaki ilişkiyi gösteren ikinci dereceden model denklemler elde edilmiştir. Bakır ve çinko liç verimi üzerine NH3 derişiminin pH’dan daha etkili bir parametre olduğu belirlenmiştir. NH3 ve NH4NO3 derişimleri ile pH için optimum değerler sırasıyla 0,38 M, 0,11 M ve 9,80 olarak bulunmuştur. Optimum koşullarda cevherdeki bakırın %82,3’ünün çinkonun ise %45,1’inin çözeltiye geçtiği belirlenmiştir. Liç sonucunda elde edilen çözeltideki Cu+2 ve Zn+2 iyonları Na2CO3 çözeltisi ile çöktürülmüş ve oluşan katı ürün 350 °C’de 6 saat süreyle kalsine edilerek Cu/Zn oksit ikili katalizörü üretilmiştir. Katalizörün ağırlıkça bakır oksit içeriği yaklaşık %44 ve çinko oksit içeriği %56 olarak tespit edilmiştir.

  • 
  • 
  İncele
• MakaleAçık Erişim2022/r/munzur/5854
  Ponza ile bakır ve kurşun iyonlarının adsorpsiyon karakteristikleri

  Karacahan, Mehmet Kayra; Demirkiran, Nizamettin; Tanaydın, Zümra Bakıcı; Ince, Muharrem

  Bu çalışmada, kesikli sistemde, ponza kullanılarak çözeltilerden Cu(II) ve Pb(II) iyonlarının uzaklaştırılması amaçlanmıştır. Adsorban miktarı etkisi (0.1-0.5g), Cu(II) ve Pb(II) iyon çözeltilerinin derişim etkisi (Cu(II) için; 3.2-31.8 ppm, Pb(II) için; 10.2-103.6 ppm), çözeltilerin pH etkisi (Cu(II) için 3-6.1(doğal pH), Pb(II) için 3-5.25(doğal pH)) gibi değişken parametrelerin etkileri incelenmiştir. Adsorban miktarının 0.4 g, çözelti iyon derişiminin 6.4 ppm ve pH değerinin 6.1 olduğu optimum şartlarda %91 bakır giderim verimi elde edilirken adsorban miktarının 0.4 g, çözelti iyon derişiminin 20.7 ppm ve pH değerinin 5.2 olduğu optimum şartlarda %97.7 kurşun giderim verimi elde edilmiştir. Deneysel olarak bulunan adsorpsiyon verilerine Langmuir, Freundlich, Temkin ve Harkins-Jura izoterm modelleri uygulanarak modellenmiş ve izoterm sabitleri hesaplanmıştır. Bakır ve kurşun iyonlarının adsorpsiyonunda Freundlich izoterm modeli deney verilerine en uygun model olarak belirlenmiştir. Bakır için ponzanın maksimum adsorplama kapasitesi 2.55 mg g⁻¹, kurşun için bu değer 10.28 mg g⁻¹ olarak bulunmuştur. Adsorpsiyon kinetiklerinin yalancı ikinci mertebeden kinetik modeline daha uyumlu olduğu belirlenmiştir. Farklı sıcaklıklarda standart serbest enerji değişimi (ΔG°), entalpi (ΔH°) ve entropi (ΔS°) değerleri belirlenmiştir. Yapılan çalışmada elde edilen sonuçlar, diğer adsorbanlarla karşılaştırıldığında ponzanın sulu çözeltilerden ağır metallerin gideriminde etkin, ekonomik ve alternatif bir adsorban malzemesi olabileceğini göstermiştir.

  • 
  AtıfOpenAlex1·TR Dizin1

  İncele
• MakaleAçık Erişim2022Scopus SJRQ1/r/munzur/2874
  Optimization of process parameters and kinetic modelling for leaching of copper from oxidized copper ore in nitric acid solutions

  TANAYDIN, Mehmet Kayra; TANAYDIN, Zümra Bakıcı; DEMIRKIRAN, Nizamettin

  The leaching behavior of Tunceli malachite mineral was investigated in nitric acid solutions by two steps to evaluate the effect of various experimental parameters. In the first step, the optimal conditions for the leaching process were determined, while in the second step, a kinetic evaluation for the process was performed. In the optimization experiments, the concentration of nitric acid, temperature, stirring speed, and solid-to-liquid ratio were selected as the independent variables, and the central composite design method (CCD) was applied to the experimental data. At the end of the experiments, the optimal values for the concentration of nitric acid, temperature, solid-to-liquid ratio and stirring speed were determined to be 0.5 mol/L, 50 °C, 0.004 g/mL and 500 r/min, respectively. Under the optimal conditions, the leaching rate was found to be 99% for 120 min of reaction time. In the kinetic evaluation tests, the effects of the concentration of nitric acid, temperature, stirring speed, solid-to-liquid ratio and particle size on the leaching rate of copper from malachite were investigated. In these tests, it was determined that the leaching rate increased with the increase in the temperature, acid concentration and stirring speed, and with the decrease in the particle size and solid-to-liquid ratio. In consequence of the kinetic analysis, it was observed that the leaching kinetics followed the mixed kinetic model, and a mathematical model for the leaching process was introduced. The activation energy for this process was calculated to be 36.23 kJ/mol.

  AtıfScopus18·WoS17·OpenAlex17

  İncele
• MakaleYalnız künye2021Scopus SJRQ2/r/munzur/3005
  Determination of Optimum Process Conditions by Central Composite Design Method and Examination of Leaching Kinetics of Smithsonite Ore Using Nitric Acid Solution

  Tanaydın, Mehmet Kayra; Bakıcı Tanaydın, Zümra; Demirkıran, Nizamettin

  The leaching behavior of Tunceli smithsonite ore in nitric acid was evaluated in two study steps including optimization of leaching process and kinetics modeling. The individual and synergistic effects of effective parameters such as nitric acid concentration, solid-to-liquid ratio, stirring speed, and temperature on the dissolution rate of zinc were investigated using central composite design. Four factors including temperature (30–50 °C), nitric acid concentration (0.2–0.5 mol/L), stirring speed (350–600 rpm), and solid-to-liquid ratio (0.004–0.01 g/L) were investigated. The dissolution percent of zinc (97%) was obtained in 120 min of leaching time: acid concentration 0.5 mol/L, temperature 50 °C, stirring speed 500 rpm, and solid–liquid ratio 2/500 g/mL at the optimum conditions obtained using the central composite design. The dissolution kinetics of smithsonite was examined according to heterogenous models and it was found that the dissolution rate was controlled by ash layer diffusion process. It was found that the leaching rate increased with increasing temperature, stirring speed, and acid concentration as well as decrescent particle size and solid/liquid ratio. The trial data were analyzed by statistical and graphical methods and the activation energy of this leaching process was determined to be 28.63 kJ·mol−1. Graphical Abstract: [Figure not available: see fulltext.].

  AtıfScopus9·WoS9·OpenAlex10

  İncele
• MakaleAçık Erişim2020/r/munzur/6719
  Adsorption of Copper and Cadmium with Perlite and Comparison of Adsorption Properties

  Karacahan, Mehmet Kayra; Demirkiran, Nizamettin; Ince, Muharrem; Bakıcı Tanaydın, Zümra

  This study, the effectiveness of perlite for the removal of Cu (II) and Cd (II) ions from aqueous medium was investigated by adsorption method. Using perlite adsorbent, parameters such as initial concentration, initial pH, adsorbent dosage and contact time affecting Cu (II) and Cd (II) ions adsorption from aqueous solutions were investigated. Initial concentration of copper (II) ions, initial pH value, adsorbent amount, contact time respectively 3.2 ppm, natural pH 6.49, 2 g, during the 180 minutes adsorption 94% of copper ions adsorbed, the initial concentration of cadmium (II) ions solution, initial pH, adsorbent amount, contact time 5.6 (ppm), natural pH 5.25, 2 g, 180 minutes, respectively, 77% adsorbed. It was determined that the adsorption data fit the Langmuir isotherm for copper ions and Freundlich isotherm for cadmium ions, and the kinetic data of copper and cadmium ions fit the false second order model. Including the thermodynamic parameters of adsorption, Gibbs free energy change (ΔG°), enthalpy (ΔH°) and entropy (ΔS°) values calculated at 20oC are for copper 3.1 kJ mol-1, -55.52 kJ mol-1, -0.2 kJ mol-1 K-1 , respectively and for cadmium, 7.14 kJ mol-1, -28.02 kJ mol-1, -0.12 kJ mol-1 K-1, respectively. The results showed that the adsorption of these metal ions on the perlite is exothermic and feasible at 20-50°C.

  AtıfTR Dizin6

  İncele
• BildiriYalnız künye2017/r/munzur/3870
  Removal of copper from aqueous solution using perlite

  Tanaydin, Mehmet Kayra; Tanaydin, Zümra Bakici; Ince, Muharrem; Demlrkiran, Nizamettin

  The wastewaters containing organic and inorganic pollutants after many industrial processes such as metal plating, mining, textile, alloy, battery and industrial chemicals, are often discharged to environment. Heavy metals among these pollutants have highly stable, toxic, non-degradable and carcinogenic characters. They affect not only ecological system, but also human health and many life forms. Therefore, these contaminants should be eliminated or reduced to allowable levels before releasing to environment. Most of heavy metals have toxic character even at low concentrations of about 0.1-0.3ppm. Treatment technologies such as filtration, ion exchange, precipitation, electrodeposition, reverse osmosis, sedimentation, and adsorption have been applied for removal of heavy metals from aqueous solutions. Adsorption is one of the most common and widely applied methods to eliminate the metal ions from waste solutions because of its simplicity and cost effectiveness. Activated carbon, clay minerals, ion exchange resins and various agricultural residues can be used as adsorbent materials in this process [1-3].

  • 
  • 
  AtıfScopus1·WoS1·OpenAlex3

  İncele