Dilek, İlhan; Taşgın, Yahya; Kanca, Muhammed Sait; Kök, Mediha; Güler, Ömer

Recently, high-entropy alloys (HEAs) have attracted significant attention due to their unique multicomponent composition and exceptional mechanical properties, such as high wear and corrosion resistance, making them superior to conventional alloys for advanced engineering applications. The effects of Al, Ti, and Mo addition on the microstructural and mechanical properties of CoCrFeNi-based HEAs were investigated. The alloys were produced via powder metallurgy and vacuum arc melting, with the addition of 2 and 3% Al, Ti, and Mo, respectively. Scanning electron microscopy (SEM), energy-dispersive x-ray spectroscopy (EDS), and x-ray diffraction (XRD) were used to perform microstructural characterization, while microhardness and wear tests were used to evaluate mechanical performance. The addition of Al and Ti enhanced the face-centered cubic phase stability and increased the hardness by improving the lattice structure. In contrast, the addition of Mo contributed to solid solution and precipitation hardening, resulting in a simpler microstructure and superior tribological performance. Among all compositions, the alloy with 3% Mo addition exhibited the highest hardness value (≈ 233.8 HV) and the lowest mass loss (4.3 mg) was observed, indicating a significant improvement in the wear resistance and mechanical strength. In conclusion, the addition of Ti and Mo to CoCrFeNi HEAs promotes solid solution, precipitation, and grain boundary hardening mechanisms, thereby enhancing microstructural integrity, hardness, and wear resistance. These findings suggest that such alloys are promising candidates for use as next-generation structural and tribological materials under demanding operational conditions.

İncele

Kanca, Muhammed Sait; Yılmaz, Demet; Tasgın, Yahya; Kök, Mediha; Güler, Seval Hale

In this study, the effects of rare earth oxides (Gd₂O₃, La₂O₃, Eu₂O₃, Pr₂O₃, Dy₂O₃, and Y₂O₃) and high-entropy oxide (GdLaEuPrDyY)₂O₃ additives on the structural, mechanical, and radiation shielding properties of copper matrix composites were investigated. XRD and SEM-EDS analyses showed that the high-entropy oxide successfully formed in a single-phase bixbyite structure after mechanical alloying and was homogeneously distributed within the copper matrix. The rare earth oxide additive significantly reduced the crystal grain size of the Cu matrix and improved its mechanical properties. Specifically, the microhardness value reached 68.3 Hv in the composite with 20% high-entropy oxide additive, representing an increase of approximately 111% compared to pure copper (32.3 Hv). Gamma shielding results showed that the rare earth oxide additive significantly increased the photon attenuation capacity. Specifically, at 242 keV energy, the Dy₂O₃ additive increased the MAC value from 0.141 cm²/g to 0.246 cm²/g, providing a 74.5% improvement. The most important result is that the composite with 20% high-entropy oxide additive showed the highest shielding performance, achieving a MAC value of 0.278 cm²/g, which is significantly superior to pure copper. Furthermore, this composite exhibited the lowest HVL and MFP values, demonstrating the highest photon shielding efficiency. Neutron shielding analyses revealed that Gd₂O₃ and high-entropy oxide additives, in particular, increased thermal neutron attenuation performance to approximately 100%. These results demonstrate that high-entropy oxide additives provide a stronger impact compared to single oxide additives, offering superior performance in both gamma and neutron shielding. Consequently, copper composites doped with (GdLaEuPrDyY)₂O₃ stand out as promising alternative shielding materials for nuclear facilities, radiation protection systems, and advanced engineering applications due to their high shielding efficiency, improved mechanical properties, and non-toxic composition.

AtıfScopus1·OpenAlex1

İncele

Güler, Ömer; Yılmaz, Demet; Kanca, Muhammed Sait; Kök, Mediha; Taşgın, Yahya

In this study, the incorporation of a high-entropy rare-earth oxide, (GdLaEuPrDyY)2O3 (RE-HEO), into a borosilicate glass matrix was investigated with the aim of improving radiation shielding performance while preserving the structural integrity of the glass. The RE-HEO was first synthesized by high-energy mechanical alloying and then introduced into the glass system at concentrations ranging from 0 to 8 wt% using a conventional melt-quenching process. The structural and microstructural properties of the prepared samples were examined using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy combined with energy-dispersive spectroscopy (SEM–EDS). The analyses confirmed that the amorphous nature of the borosilicate glass was maintained and that the rare-earth elements were homogeneously distributed within the matrix. The radiation shielding performance was evaluated experimentally using Am-241, Ba-133, and Ra-226 gamma sources, and supported by theoretical calculations of key parameters including mass attenuation coefficient (MAC), half-value layer (HVL), mean free path (MFP), effective atomic number (Zeff), exposure buildup factor (EBF), and fast neutron removal cross-section (ΣR). The results showed that increasing RE-HEO content leads to a noticeable improvement in gamma-ray attenuation. In particular, the sample containing 8 wt% RE-HEO exhibited a MAC value of 0.131 cm2/g and an HVL of 2.03 cm at 356 keV, indicating shielding performance comparable to that of conventional lead-containing glasses. In addition, irradiation tests performed using a Co-60 gamma source revealed that the amorphous structure remains stable after exposure. Overall, the findings suggest that RE-HEO-doped borosilicate glass can be considered a promising lead-free alternative for radiation shielding applications.

AtıfScopus1·WoS1·OpenAlex1

İncele

Kanca, Muhammed Sait

In this study, CuAlMn alloys, a popular Cu-based shape memory alloy, were chosen because they exhibit superior shape memory properties and improved ductility compared to other Cu-based SMAs. The rare earth element Nd (neodymium) was added to CuAlMn alloy at the specified atomic percentages in the composition Cu70-xAl24Mn6Ndx(x = 0,2,4,8) and their thermal behavior, crystal structure, surface morphology and magnetic properties were investigated after fabrication. As a result of the thermal analysis measurements, it was observed that for low Nd ratios, the austenite phase transformation initial temperature of the CuAlMn alloy was increased, while at high Nd ratios, a decrease in the shape memory property was detected. Martensitic phase and precipitate phase α phase were observed in the crystal structure properties of CuAlMn alloys without and with Nd doping. These results were also detected in surface morphology observations. In addition, the crystal size decreased from 135 to 105 nm with Nd doping. As a result of magnetic measurements, CuAlMn ternary shape memory alloy was found to be paramagnetic at room temperature. Magnetic susceptibility values of the alloys showing paramagnetic magnetic properties were calculated as 11.5 × 10–6, 12.5 × 10–6, 9.15 × 10–6 and 6.15 × 10–6 emu.Oe−1.g−1, respectively. According to these results, the magnetic susceptibility value decreased with increasing Nd ratio.

AtıfScopus3·WoS3·OpenAlex3

İncele

Kök, Mediha; Kanca, Muhammed Sait; Say, Yakup; Saydam, Sinan; Dağdelen, Fethi; Qader, Ibrahim Nazem

NiTi-based memory alloys are often used as intracorporeal implant materials because of their superelasticity and shape memory properties. However, over time, the release of nickel from the NiTi alloy into the body becomes unfavorable; therefore, studies should be conducted to reduce the negative impact of nickel leakage. In this study, the biocompatible selenium element was used to coat NiTi alloys with different thicknesses. The coating process was performed using the thermal evaporation technique. Scanning electron microscopy-Energy Dispersive X-ray Analysis measurements revealed that the surfaces of the samples were well covered. Also, the atomic force microscope device determined the surface roughness of the alloys. The roughness of the surface increased after the coating process. The Tafel test was accomplished to determine the biocompatibility of the coated and uncoated alloys in an artificial body fluid. The corrosion test reveals that Se-coated NiTi alloys have high corrosion resistance.

İncele

Niksarlıoğlu, Seçil; Akman, Ferdi; Agar, Osman; Kaçal, Mustafa Recep; Kanca, Muhammed Sait

In this study, the gamma ray attenuation characteristics for CuAlNi shape memory alloys with different proportions of Sn doping was investigated. We determined the mass attenuation coefficient (μ/ρ) of CuAlNiSn alloys both experimentally and theoretically within an energy range of 59.5–1332.5 keV. The experimental measurements were made using a high purity Germanium detector (HPGe) and theoretical calculations were made using WinXCOM program. To evaluate the gamma radiation shielding abilities of the alloy samples, the obtained (μ/ρ) values were used to determine the gamma protection parameters μ, HVL, TVL, MFP, and Zeff. In addition, the radiation protection efficiency (RPE) parameter was determined using gamma ray intensities in the absence and presence of the attenuator. Further analysis of the samples was conducted using a Rigaku Miniflex 600 model computer-controlled X-ray diffractometer (CuKα & λ = 1.5405 A0). The crystallographic structure of the alloys before and after irradiation was investigated. Other analysis which include EDX analysis (to investigate the chemical content) and SEM analysis (to investigate the microstructure) were conducted. According to result outcomes, gamma ray radiation did not affect the shape memory properties of structure. Another interesting observation is that, the radiation attenuation properties increase with increasing Sn concentration. Finally, we discovered that the CuAlNiSn4 alloy (which has the highest doping rate) provides good protection especially at low energy levels.

AtıfScopus5·OpenAlex6

İncele

Taşgin, Yahya; Pekdemir, Mustafa Ersin; Yilmaz, Mücahit; Kanca, Muhammed Sait; Kök, Mediha

Rare earth elements (RRE), due to their unique magnetic, electrical, and optical properties, are an important group of elements demanded in many application areas from machine technology to the health industry. In this study, new composites were obtained by mixing Erbium oxide (Er2O3), one of the rare earth element oxides, into PCL–PEG blend, which is also an important material group, in different ratios. The characteristic functional groups of the obtained polymer blend/Er2O3 nanocomposites were determined by the ATR-IR, and as the erbium oxide ratio increased, characteristic peaks of the polymers in the blend as well as characteristic signals of the Er–O–Er bond were found. When the thermal behavior of the obtained composites was examined, it was observed that the polymer blend exhibited miscible blend properties and the melting temperature of the polymer blend increased as the Er2O3 ratio increased. In addition, it was determined that the thermal stability of the composite increased significantly. X-ray measurements of composites at room temperature support other measurement results. It was determined that the presence of Er-RRE oxide increased the crystal structure feature in the polymer blend composite. Gamma radiation shielding capabilities of polymer materials containing different erbium ratios were investigated by calculating shielding parameters such as half value layer (HVL), radiation protection efficiency (RPE), and mean free path (MFP). Cs-137 and Co-60 radioactive sources were used as gamma sources. According to the obtained measurement results, Erbium oxide increased the absorption property of the polymer composite material. Graphical abstract: [Figure not available: see fulltext.].

AtıfScopus26·WoS28·OpenAlex29

İncele

Pekdemir, Mustafa Ersin; Kök, Mediha; Kanca, Muhammed Sait; Özen Öner, Ecem; Pekdemir, Sibel; Inci, Şule; Kirbağ, Sevda; Tatar, Beyhan

Recently, there has been a great demand for boron-containing compounds (BCCs) with unique biological properties. The demand for the use of these compounds not alone but as additives in composite materials is increasing day by day. In this study, the effect of adding B2O3 compound to the blend of PLA and PEG polymers, which is an important biocompatible shape memory polymer, was investigated. In order to examine the effect of increasing B2O3 additive on the thermal properties of PLA-PEG blend, it was determined by using a Differential Scanning Calorimetry (DSC) and thermogravimetric analyzer (TGA), and it was seen that while the melting temperature of PEG decreased, the melting temperature of PLA increased. In addition, when the thermal stability of the composites was examined, increasing of thermal stability was observed with the addition of B2O3 and a three-step degradation occurred. It was determined that the B2O3/PLA-PEG composite was homogeneous by taking X-ray measurements and SEM measurements. The antimicrobial property of the PLA-PEG blend improved with the increasing B2O3 contribution were observed from the antimicrobial activity measurements of the composite against 4 different bacteria. However, it was determined that the PLA-PEG blend preserved its shape memory effect with increasing diboron trioxide contribution.

AtıfScopus13·OpenAlex16

İncele

Say, Yakup; Kanca, Muhammed Sait; Kök, Mediha

NiTinol alloy has recently been in high demand in biomaterials applications due to its excellent superelasticity and shape memory properties. This demand has increased the studies on improving the negative properties of the NiTinol alloy, even if it is less. In this study, it was aimed to coat the nickel element in the NiTi alloy with biocompatible elements in order to prevent it from secreting its toxic effect after its implantation into the body. In accordance with this purpose, NiTi shape memory alloys were coated with silver and copper element by using thermal evaporation system, and the surface morphology of the alloys after coating was investigated by SEM–EDX (Scanning Electron microscope), and AFM (Atomic force Microscope). After the measurements, it was observed that the coating was successful and homogeneously distributed on the entire surface of the alloy. In addition, an important and positive result was that, the roughness value of the NiTi alloy was decreased with the coating. The change in the crystal structure of the uncoated and coated NiTi alloy was evaluated using an X-ray device, and it was observed that the silver and copper element peaks were formed along with the B2 phase, which is the main phase of the NiTi alloy. In order to examine the effect of coating on the biocompatibility of NiTi alloy, electrochemical test was performed by rapid measurement method in simulated body fluid and corrosion behavior was investigated. According to these experiments, it was concluded that silver plating is more successful in term of biocompatibility than copper coating.

AtıfScopus4·WoS3·OpenAlex4

İncele

Taşgin, Yahya; Kanca, Muhammed Sait; Kök, Mediha

In this study, in order to add different properties and functions to inorganic amorphous glasses, the applicability and effects of the thin film coating produced by thermal evaporation method were examined by metallographically imaging the effects of 3%–5% CeO2 and Tm2O3 rare earth elements (REE) oxide added to selenium to change the morphology of the glass surface. As a result of the study, it has been proved that CeO 2 and Tm2O3 added to selenium can be coated by thermal evaporation method with AFM images taken from the glass surface and metallographic analyses (SEM, EDX, Mapping). The lowest roughness value was observed in 95Se–5CeO2 coating glass substrate. In all coatings, selenium, which is the main sample, was found to be active, and XRD measurements showed that the thin films were formed by agglomeration on the (101) plane. According to UV-VIS measurements, the lowest optical band energy range was observed in the 95Se–5CeO2 coating.

AtıfScopus11·WoS10·OpenAlex12

İncele