Sürdürülebilir Kalkınma Amaçları
Yayınlar
- MakaleYalnız künye2022Scopus SJRQ1Heat and mass transfer mechanism and control strategy of clean low carbon combustion technology in the novel-type coke oven flue with MILD combustion
Xu, Qian; Shen, Meng; Xie, Kai; Zhang, Hui; Akkurt, Nevzat; Wang, Jiulong; Xiong, Yaxuan; Shi, Kejian; Chen, Xingli; Lv, Qian
In the field of emission reduction, considering the limitations of single clean combustion technology and joint control of carbon emission, the application of Technology of Mixed-Gas (TMG), Technology of Low-calorific Value Gas (TLVG) and Technology of Low Oxygen Combustion (TLOC) in the Novel-type Coke Oven Flue with MILD Combustion (MILD-NCOF) was realized. By adjusting the ratio of coke oven gas to blast furnace gas (α), the ratio of flue gas to gas (β) and the ratio of flue gas to air (γ), the heat and mass transfer mechanism of combustion process in MILD-NCOF was researched, the dual emission control system and the regulation strategy of pollutant and carbon emissions were established. The results showed that with the increase of α, β and γ, the fluidity of gas and the reaction rate of combustible components in the fire path were improved, the heat and mass transfer was enhanced, and the effect of dual emission reduction of pollutants and carbon emissions was improved. When the mixing ratio α was 0.6, Tave was reached at 1594.93 K. The NOx concentration at the outlet was 116.34 mg/m3, and the sum of the molar concentrations of CO and CO2 at the outlet was reduced to 1.440 × 10−1. When the mixing ratio β was 2.4, Tave was reached at 1518.73 K, the NOx concentration at the outlet was 128.42 mg/m3, and the sum of the molar concentrations of CO and CO2 at the outlet was 1.127 × 10−1. When the mixing ratio γ was 0.6, Tave was reached at 1627.28 K, the NOx concentration at the outlet was 142.73 mg/m3, and the sum of the molar concentrations of CO and CO2 was reduced to 1.128 × 10−1, which could meet the dual standards of clean production and low-carbon environmental protection of MILD-NCOF.
AtıfScopus30OpenAlex36
İncele - MakaleYalnız künye2022Scopus SJRQ1Numerical evaluation of convective heat transfer properties of two-dimensional rotating PCM melt in the unilaterally heated rectangular container
Liu, Dinghai; Xie, Kai; Zhang, Hui; Qiang, Yujie; Yang, Di; Wang, Zhaoxiao; Zhu, Lidong; Akkurt, Nevzat; Du, Yanping; Shen, Meng
This paper carried out numerical investigations on the flow and heat transfer characteristics of a phase change with two-dimensional rotation of the three-dimensional paraffin (RT -27)-filled rectangular encapsulated container (PCM-REC) in space. A three-dimensional transient numerical heat transfer model was established and the enthalpy method was used to simulate the solid-liquid phase transition process and the flow evolution at the PCM interface. In this paper, the solid-liquid interface distribution, temperature distribution and melting time of PCM in PCM-REC heated at a constant temperature on one side were compared when rotated at different angles (0°, arctan (0.4), 2arctan (0.4) and 90°) along the heating direction and vertical heating direction. Results demonstrated that the peak value of maximum natural convection velocity increased from 0.0072 m/s to 0.0184 m/s with increasing radial height when PCM-REC was rotated in vertical heating direction. When PCM-REC was rotated in two dimensions by the same angle, the melting time was fastest when γ was an obtuse angle, and with the increase of the obtuse angle, the melting time shortened from 17 min to 6 min; when γ was an acute angle, the melting time was slowest, and with the decrease of the acute angle, the melting time lengthened from 49 min to 288 min.
AtıfScopus35OpenAlex40İncele - MakaleAçık Erişim2022Scopus SJRQ1Experimental study on synergistic enhancement of thermal performance of a closed two-phase thermosyphon by a TiO2nanofluid doped with Al2O3
Xu, Qian; Yang, Gang; Jia, Shuhui; Wang, Zhaoxiao; Akkurt, Nevzat; Zhang, Hui; Zhou, Qiang; Shen, Meng; Yang, Di; Zhu, Lidong
The heat transfer performance of two-phase closed thermosyphon solar collectors (TPCTs) can be improved by adding nanoparticles to the conventional working fluid, but it is necessary to ensure good rheological properties while improving the heat transfer performance. Therefore, spherical (TiO2) nanoparticles with good rheological properties and rod-shaped (Al2O3) nanoparticles with high thermal conductivity were mixed and applied to the TPCT. First, the effects of individual factors such as the concentration of nanoparticles and the operating parameters on the thermal performance of the TPCT were investigated and a regression analysis was performed. Then, the joint effect of inclination angle and filling ratio on the thermal performance of TPCT was further investigated by orthogonal experiment. The results show that doping TiO2 with Al2O3 can further improve the thermal performance of TPCT. For the volume concentration of 0.6% of nanoparticles, filling ratio of 50% and inclination angle of 80°, the best heat transfer performance of TPCT was achieved. Compared with the deionized water (DW), the thermal resistance of the single (TiO2-H2O) and hybrid (Al2O3+TiO2-H2O) nanofluid TPCT is reduced by 10.7% and 13.4%, the thermal efficiency is increased by 11.0% and 13.7%, and the equivalent heat transfer coefficient is increased by 16.2% and 18.7%, respectively.
AtıfScopus38OpenAlex41İncele - MakaleYalnız künye2021Scopus SJRQ2Effect of the Mixing Structure Parameters of a Self-reflux Burner on Combustion Characteristics and NOx Emission
Xu, Qian; Shen, Meng; Shi, Kejian; Liu, Zhihui; Akkurt, Nevzat; Xiong, Yaxuan; Liu, Lin; Feng, Junxiao; Wang, Jiulong
To solve the problem of low efficiency of NOx emission reduction in self-reflux burners, this study is based on the concept of coordinated control of self-reflux burner structural and thermal parameters. After completing the structural design and optimization of thermal parameters, we continue to adjust the two key structural parameters: the nozzle axis distance and the length of the cylindrical section, to minimize NOx emissions. These are the two parameters that chiefly affect the mixing of flue gas and fuel gas. The results show that increasing nozzle axis distance can delay the mixing of gas and air and create a more uniform oxygen concentration field for the combustion process. The maximum combustion temperature is reduced from 1973.65 K to 1935.88 K and the volume fraction of NOx in the flue gas is reduced from 188.08×10−6 to 143.47×10−6. However, compared with the nozzle axis distance, the length of the cylindrical section of the burner has little effect on the mixing of the flow field. Under different cylindrical section lengths, the maximum combustion temperature does not change more than 3 K, and the volume fraction of NOx in the flue gas changes within 5×10−6.
AtıfScopus3OpenAlex2İncele