Sürdürülebilir Kalkınma Amaçları
Yayınlar
- MakaleYalnız künye2022Scopus SJRQ1Heat transfer performance by forced convection of microencapsulated phase change material-latent functional thermal fluid flowing in a mini-channels heat sink
Xu, Qian; Zhu, Lidong; Yan, Xinyu; Yang, Jingbin; Wang, Zhaoxiao; Liu, DingHai; Yang, Gang; Chen, Xingli; Akkurt, Nevzat; Liu, Lin
Conventional single-phase coolants have not been able to meet the high cooling requirements of electronic devices. Microencapsulated phase change material-latent functional thermal fluid (MPCM-LFTF), a solid–liquid two-phase cooling medium, has the dual advantages of active liquid cooling and passive phase change material cooling. However, it also increases the power consumption in the mini-channels, and the cooling efficiency of MPCM-LFTF in practical applications needs to be further studied. A new MPCM-LFTF was prepared by paraffin melamine resin MPCM and base fluid (absolute ethanol and deionized water) in this work. The heat transfer performance and hydrodynamic properties were investigated using the dimensionless wall temperature and friction factor, respectively. The efficiency factor was introduced to evaluate the cooling efficiency of MPCM-LFTF in mini-channels. The experimental results showed that the addition of MPCM increased the viscosity of MPCM-LFTF, which increased the friction factor. MPCM-LFTF with a mass fraction of 15 % had the best effect of temperature control and reduced the dimensionless wall temperature by 40.5 %. However, considering the characteristics of flow resistance and improved heat transfer, MPCM-LFTF with a mass fraction of 10 % had the highest cooling efficiency and the efficiency factor was 57.0 % higher than that of the base fluid.
AtıfScopus35OpenAlex36
İncele - MakaleYalnız künye2022Scopus SJRQ1Numerical evaluation of convective heat transfer properties of two-dimensional rotating PCM melt in the unilaterally heated rectangular container
Liu, Dinghai; Xie, Kai; Zhang, Hui; Qiang, Yujie; Yang, Di; Wang, Zhaoxiao; Zhu, Lidong; Akkurt, Nevzat; Du, Yanping; Shen, Meng
This paper carried out numerical investigations on the flow and heat transfer characteristics of a phase change with two-dimensional rotation of the three-dimensional paraffin (RT -27)-filled rectangular encapsulated container (PCM-REC) in space. A three-dimensional transient numerical heat transfer model was established and the enthalpy method was used to simulate the solid-liquid phase transition process and the flow evolution at the PCM interface. In this paper, the solid-liquid interface distribution, temperature distribution and melting time of PCM in PCM-REC heated at a constant temperature on one side were compared when rotated at different angles (0°, arctan (0.4), 2arctan (0.4) and 90°) along the heating direction and vertical heating direction. Results demonstrated that the peak value of maximum natural convection velocity increased from 0.0072 m/s to 0.0184 m/s with increasing radial height when PCM-REC was rotated in vertical heating direction. When PCM-REC was rotated in two dimensions by the same angle, the melting time was fastest when γ was an obtuse angle, and with the increase of the obtuse angle, the melting time shortened from 17 min to 6 min; when γ was an acute angle, the melting time was slowest, and with the decrease of the acute angle, the melting time lengthened from 49 min to 288 min.
AtıfScopus35OpenAlex40İncele - MakaleAçık Erişim2022Scopus SJRQ1Experimental study on heat transfer properties of gravity heat pipes in single/hybrid nanofluids and inclination angles
Wang, Zhaoxiao; Zhang, Hui; Yin, Lei; Yang, Di; Yang, Gang; Akkurt, Nevzat; Liu, Dinghai; Zhu, Lidong; Qiang, Yujie; Yu, Fan
In order to meet the working requirements of heat pipes under complex working conditions and high heat flux density, and propose corresponding thermal management solutions. In this paper, the single and hybrid nanofluids (TiO2-H2O, Al2O3-H2O, Al2O3+TiO2-H2O) with mass fraction of 5% under the gradient of gravity heat pipe at 50°, 60°, 70°, 80°, 90° are studied. The changes in thermal resistance, thermal efficiency and equivalent heat transfer coefficient of water were compared with deionized water. The results are as follows: The overall efficiency of gravity heat pipe ranges from 70% to 85%. Compared with deionized water, the nanofluid can effectively improve the heat transfer. At different inclination angles, the hybrid nanofluid with the same mass fraction shows the reverse trend compared with the single nanofluid by decreasing the thermal resistance of the heat pipe and increasing the heat transfer efficiency. At an inclination angle of 70°, the heat transfer efficiency of the nanofluid Al2O3+TiO2-H2O is 6.8% weaker compared to TiO2-H2O and 4.5% weaker compared to Al2O3-H2O. At a tilt angle of 60°, the heat transfer capacity of Al2O3+TiO2-H2O nanofluid increases by 7.3% compared to TiO2-H2O and by 5.6% compared to Al2O3-H2O.
AtıfScopus47OpenAlex45İncele - MakaleAçık Erişim2022Scopus SJRQ1Experimental study on synergistic enhancement of thermal performance of a closed two-phase thermosyphon by a TiO2nanofluid doped with Al2O3
Xu, Qian; Yang, Gang; Jia, Shuhui; Wang, Zhaoxiao; Akkurt, Nevzat; Zhang, Hui; Zhou, Qiang; Shen, Meng; Yang, Di; Zhu, Lidong
The heat transfer performance of two-phase closed thermosyphon solar collectors (TPCTs) can be improved by adding nanoparticles to the conventional working fluid, but it is necessary to ensure good rheological properties while improving the heat transfer performance. Therefore, spherical (TiO2) nanoparticles with good rheological properties and rod-shaped (Al2O3) nanoparticles with high thermal conductivity were mixed and applied to the TPCT. First, the effects of individual factors such as the concentration of nanoparticles and the operating parameters on the thermal performance of the TPCT were investigated and a regression analysis was performed. Then, the joint effect of inclination angle and filling ratio on the thermal performance of TPCT was further investigated by orthogonal experiment. The results show that doping TiO2 with Al2O3 can further improve the thermal performance of TPCT. For the volume concentration of 0.6% of nanoparticles, filling ratio of 50% and inclination angle of 80°, the best heat transfer performance of TPCT was achieved. Compared with the deionized water (DW), the thermal resistance of the single (TiO2-H2O) and hybrid (Al2O3+TiO2-H2O) nanofluid TPCT is reduced by 10.7% and 13.4%, the thermal efficiency is increased by 11.0% and 13.7%, and the equivalent heat transfer coefficient is increased by 16.2% and 18.7%, respectively.
AtıfScopus38OpenAlex41İncele