Sürdürülebilir Kalkınma Amaçları
Yayınlar
- DüzeltmeAçık Erişim2026Scopus SJRQ1Correction: 2D MHD Mixed Convection in a Zigzag Trapezoidal Thermal Energy Storage System Using NEPCM (Nanomaterials, (2022), 12, 19, (3270), 10.3390/nano12193270)
Abderrahmane, Aissa; Younis, Obai; Al-Khaleel, Mohammad; Laidoudi, Houssem; Akkurt, Nevzat; Guedri, Kamel; Marzouki, Riadh
There were errors in the original publication [1]. In Abstract and Introduction, any reference to “heat transfer (HT) irreversibility,” “fluid friction (FF) irreversibility,” or “Bejan number” is erroneous and should be removed. Any reference to “wave number” should be corrected to “zigzag number,” which is the relevant parameter in the study. The corrected Abstract and the corrected sentence in the last paragraph of the Introduction appear below, respectively. In a magnetic field, two-dimensional (2D) mixed convection is investigated within a zigzagged trapezoidal chamber. The lower side of the trapezoidal chamber is irregular, in particular, a zigzagged wall with different zigzag numbers N. The fluid particles move in the room due to the motion of the upper wall, while the porosity-enthalpy approach represents the melting process. The thermal parameters of the fluid are enhanced by what is called a nano-encapsulated phase change material (NEPCM) consisting of polyurethane as the shell and a nonadecane as the core, while water is used as the base fluid. In order to treat the governing equations, the well-known Galerkin finite element method (GFEM) is applied. In addition, the heat transfer (HT) and the dynamic behavior of flow are treated in terms of average Nusselt number and contours of streamlines. The main results show that the melt band curve of heat capacity behaves almost parabolically at smaller values of Reynolds number (Re) and larger values of Hartmann number (Ha). Moreover, minimizing the zigzag number is better in order to obtain a higher heat transfer rate. In addition, a comparative study of the heat transfer and the dynamic behavior of flow in terms of average Nusselt number and contours of streamlines has been presented. In Section 2.1. Mathematical Modeling and Equations, Paragraph 3 and Paragraph 4, the term of porosity must be added to the momentum equations. The Equations (2), (3), (8) and (9) should be updated to the following: (Formula presented.) (Formula presented.) (Formula presented.) (Formula presented.) In Section 2.1. Mathematical Modeling and Equations, Paragraph 4, Paragraph 5 and Paragraph 9, there is no cylinder inside the cavity, and any reference to a “cylinder” or “diameter D” is incorrect and should be disregarded. The pressure in Equation (6), the Reynolds Number in Equation (11) and the definition for the average Nusselt number at the zigzag wall in Equation (16) should be updated to the following: (Formula presented.) (Formula presented.) (Formula presented.) The authors state that the scientific conclusions are unaffected. This correction was approved by the Academic Editor. The original publication has also been updated.
- MakaleYalnız künye2023Scopus SJRQ1Energy, exergy and cost analysis of different hemispherical solar distillers: A comparative study
Hadi Attia, Mohammed El; Hussein, Ahmed Kadhim; Radhakrishnan, Ganesh; Vaithilingam, Sivakumar; Younis, Obai; Akkurt, Nevzat
The experimental study of the results of reflective aluminum foils, metal sheets, and phosphate granules on the productivity and efficiency of hemispherical solar stills was given throughout this work under the solar conditions of the city of El-Oued (Algeria). Solar stills were designed, manufactured, and tested in August 2020. A standard hemispherical solar still was made of wood and coated with black silicon. It was considered a traditional solar still. Although it was compared to traditional solar stills, it was improved by covering its side walls with reflective aluminum foil, zinc metal sheets, and copper sheets. It had been found that the productivity of the modified still was 8.67%, 29.08%, and 42.35%, respectively, on top of that of the traditional solar still. This could be due to the activity of the foils and metals, which reflect more radiation and store energy, increasing the temperature of the salt water in the basin. In the second experiment, three modified solar stills in line with aluminum foil and phosphate granules (30 g/L), zinc metal sheet and phosphate granules, and copper metal sheet and phosphate granules were collectively used. It had been found that the productivity of the modified solar still with aluminum foil and phosphate granules (the improvement rate is 30.61%) was on the far side of that with zinc metal sheets and phosphate granules (the improvement rate is 49.961%) and copper metal sheets and phosphate granules (the improvement rate is 62.24%).
AtıfScopus37OpenAlex34
İncele - MakaleYalnız künye2023Scopus SJRQ1Buoyancy-driven flow and thermal activity of nano-enhanced phase change material in inversed U-shaped chamber
Younis, Obai; Abderrahmane, Aissa; Laidoudi, Houssem; Akkurt, Nevzat; Fadhl, Bandar M.; Guedri, Kamel
This work aims to contribute to the positive evolution towards a green world and green energy by studying the natural convection of Nano-Enhanced Phase Change Material NEPCM in an inverted U-shaped cavity. The side walls of the cavity are kept at a cold temperature, while the upper corrugated wall and the lower wall are insulated with the expectation of the hot square body. The governing equations were solved numerically using the Galerkin finite element method (GFEM). The effects of the following factors on the heat transfer rate are presented and discussed: Rayleigh number (Ra = 103–106), number of ripples of the upper wall (N = 1–4), position of the square body (left, centre, and right), volume fraction of nanoparticles (ϕ = 0–0.08), and magnetic field strength (Ha = 0–100). It was found that the effect of N on the heat transfer rate was insignificant, while increasing ϕ reduced the heat transfer rate. In addition, placing the square body near the cold sidewalls (left or right position) improved the averaged Nusselt number (Nuavg), especially at low values of Ra. At the highest Ra studied, increasing Ha reduced the Nuavg by 15 %.
AtıfScopus11OpenAlex9İncele - Derleme MakaleYalnız künye2022Scopus SJRQ1Floating solar stills and floating solar-driven membranes: Recent advances and overview of designs, performance and modern combinations
Rashid, Farhan Lafta; Al-Obaidi, Mudhar A.; Hussein, Ahmed Kadhim; Akkurt, Nevzat; Ali, Bagh; Younis, Obai
For life to exist on earth, there must be water. Freshwater resources are in short supply due to industrialization and the world's rapid population expansion. Growing water shortage argues that using passive solar stills is the best and most practical solution in the world's arid and semi-arid regions. For applications in distant or rural coastal areas, floating solar stills are an appropriate technique. To provide accessibility to a wider population, the gadget should be constructed using inexpensive materials that are easily accessible nearby. However, the low-cost materials typically do not have the optimum physical characteristics, which reduces the overall performance of solar stills. This study intends to deliver a comprehensive review that summarizes recent research developments and gives a rundown of experimental, numerical, and experimental and numerical studies on floating solar stills and floating solar-driven membranes. This article also looks at a few more setups, researched parameters, and result-finding issues. Research on floating solar is currently ongoing, and recommendations for further research projects have been made in light of the study's findings.
AtıfScopus63OpenAlex59İncele - Derleme MakaleAçık Erişim2022Scopus SJRQ1Inverted Solar Stills: A Comprehensive Review of Designs, Mathematical Models, Performance, and Modern Combinations
Hussein, Ahmed Kadhim; Rashid, Farhan Lafta; Abed, Azher M.; Al-Khaleel, Mohammad; Togun, Hussein; Ali, Bagh; Akkurt, Nevzat; Malekshah, Emad Hasani; Biswal, Uddhaba; Al-Obaidi, Mudhar A.
Fresh water is scarce, making it a worldwide issue. In order to address global freshwater demand, a filtration technique is needed. Solar distillation (SD) that purifies brackish and sub-terranean water has been proven to be a promising green technology. It produces distilled water which can be used as potable water for drinking and other purposes. The designs, operations, and configurations of several inverted solar stills are thoroughly examined in this article. All techniques for solar water distillation to separate saltwater from freshwater have the same fundamental idea. It has been demonstrated that for a specified mass of water in the top basin, the daily output of an inverted absorber double-basin solar still (IASS) grows with increasing water depth in the bottom basin. Nevertheless, as the water depth in the bottom basin rises from 1 cm to 5 cm, the output of an inverted absorber double-basin solar system falls by about 27%. At water depths of 4, 6, and 8 cm, the daily yields from inverted absorber solar stills paired with a refrigeration cycle (RIASS) were 6.4, 10.08, and 9.5 L/day, respectively. The results also showed a substantial rise in water temperature in the inverted absorber solar still as a result of lower bottom heat loss and larger absorptivity. In this study, the emphasis on energy, efficiency, and environmental concerns remains with the modified multi-wick basin-type inverted absorber solar panel. The performance of the inverted trickling solar still was assessed with a 60 ppm average salinity under various sun radiation, feed water flow rate, and existence conditions for natural convection. It was found that the still could produce 2.55 L/day m2 of fresh water, a 15% increase. Brackish water with a salinity of 6000 ppm was used to test the still in November at tilt angles of 47◦ and 32◦ . Condensate production at the specified angles was 2.8 and 2 L/d, respectively. A total output of 6.907, 5.681, and 4.650 kg/m2 /day was also generated using the modified multi-wick basin-type inverted absorber solar still (MMWBIASS) at water depths of 1, 2, and 3 cm, respectively. With black cotton wicks, the MMWBIASS had a total thermal efficiency of 34.04%, 28.17%, and 23.61%.
AtıfScopus43OpenAlex47İncele - MakaleAçık Erişim2022Scopus SJRQ12D MHD Mixed Convection in a Zigzag Trapezoidal Thermal Energy Storage System Using NEPCM
Abderrahmane, Aissa; Younis, Obai; Al-Khaleel, Mohammad; Laidoudi, Houssem; Akkurt, Nevzat; Guedri, Kamel; Marzouki, Riadh
In a magnetic field, two-dimensional (2D) mixed convection is investigated within a zigzagged trapezoidal chamber. The lower side of the trapezoidal chamber is irregular, in particular, a zigzagged wall with different zigzag numbers N. The fluid particles move in the room due to the motion of the upper wall, while the porosity-enthalpy approach represents the melting process. The thermal parameters of the fluid are enhanced by what is called a nano-encapsulated phase change material (NEPCM) consisting of polyurethane as the shell and a nonadecane as the core, while water is used as the base fluid. In order to treat the governing equations, the well-known Galerkin finite element method (GFEM) is applied. In addition, the heat transfer (HT) and the dynamic behavior of flow are treated in terms of average Nusselt number and contours of streamlines. The main results show that the melt band curve of heat capacity behaves almost parabolically at smaller values of Reynolds number (Re) and larger values of Hartmann number (Ha). Moreover, minimizing the zigzag number is better in order to obtain a higher heat transfer rate.
AtıfScopus30OpenAlex34
İncele