Sürdürülebilir Kalkınma Amaçları
Yazarlar
Yayınlar
- MakaleYalnız künye2025Scopus SJRQ2Experimental comparison of conventional and ultrasonic-assisted high-speed drilling of glass fiber reinforced epoxy composites
Ağar, Salih; Mahmat, Aybars; Doğan, Akar
Glass fiber reinforced epoxy composites are favored in several industries, including automotive and aerospace, owing to their superior strength-to-weight ratio. Drilling is a prevalent machining procedure employed to add fasteners for laminate assembly. Nonetheless, drilling these composites presents significant challenges due to the abrasive characteristics of the reinforcement, necessitating an examination of machining performance. During the drilling of composites, cutting temperature, thrust force, and delamination damage are primary concerns. In recent years, high-speed ultrasonic drilling, an innovative machining technique designed to address these challenges, has garnered significant interest. This investigation involved high-speed ultrasonic drilling and conventional drilling of glass fiber reinforced epoxy material. In the studies, optimal conditions were studied by evaluating thrust force, cutting temperature, and delamination damage by varying speeds, feed rates, and frequencies. The thrust force was 11 N in the traditional approach at 40,000 rpm, but it was recorded at 9 N with the ultrasonic method. Moreover, with ultrasonic drilling, cutting temperatures decreased by over 25% relative to traditional drilling, attributable to the harmonic motion that dissipates heat in the drilling zone. Analysis of the drilling region revealed a notable enhancement in damage, particularly in delamination, with the application of ultrasonic drilling. The experimental results indicate that ultrasonic machining enhances machining performance.
- MakaleYalnız künye2023Scopus SJRQ2Effect of impactor nose form on the impact behavior of reinforced composite materials
Dogan, Sonay; Arman, Yusuf; Dogan, Akar
The goal of the present study is to investigate the influence of impactor shape on the low-velocity impact behavior of the composite panels manufactured with different reinforcement materials at the same thicknesses, experimentally. Kevlar, carbon, S-2 glass woven fabric and epoxy matrix have been used to manufacture thermoset composites with the vacuum-assisted resin infusion molding method. The Fractovis plus test machine with a 12.7 mm diameter hemispherical and two different conical impactor noses was used to perform impact tests. The effects of impactor shapes on the low-velocity impact behavior have been compared for 20 J, 40 J, and 60 J energy levels. Although at the same impact energy level, S-2 glass fiber-reinforced epoxy specimens have a higher perforation threshold than carbon and Kevlar fiber-reinforced epoxy. Because to achieve the same thickness, the number of S-2 glass layers was greater than the number of carbon and Kevlar layers. Additionally, the form of the impactor greatly influenced the perforation threshold.
AtıfScopus7WoS7OpenAlex6
İncele - Yüksek Lisans TeziAçık Erişim2022Doğal elyaf takviyeli kompozit malzemelerin vakum destekli reçine transfer kalıplama yöntemiyle üretilerek mekanik ve metalografik özelliklerinin incelenmesi
Seçkin Kandemir
Bu çalışmanın amacı, üretilen doğal elyaf takviyeli epoksi matrisli kompozit malzemelerin mekanik ve metalografik özelliklerinin araştırılması ayrıca doğal elyaf takviyeli kompozit malzemeler ile sentetik elyaf takviyeli epoksi matrisli kompozit malzemelerin mekanik ve metalografik özelliklerinin karşılaştırılmasıdır. Bu amaçla doğal takviye malzemesi olarak jüt, keten, kenevir, pamuk, yün, sisal ve Hindistan cevizi elyafları kullanılmıştır. Sentetik takviye malzemesi olarak cam ve karbon elyafları kullanılmıştır. Kompozit malzemelerin üretimi vakum destekli reçine transfer infüzyon yöntemiyle gerçekleştirilmiştir. Üretilen kompozit malzemelerin mekanik özelliklerini belirlemek için numunelere çekme testi uygulanmıştır. Çekme testleri ile numunelerin gerilme – yüzde uzama grafikleri oluşturulmuş, kopma gerilmesi ve maksimum uzama değerleri elde edilmiştir. Üretilen numunelerin SEM analizleri yapılmıştır.
- MakaleYalnız künye2022Scopus SJRQ2Single and repeated low-velocity impact response of E-glass fiber-reinforced epoxy and polypropylene composites for different impactor shapes
Dogan, Akar
This study focuses on the effects of low-velocity impact (LVI) response of thermoset (TS) and thermoplastic (TP) matrix-based composites. In this study, the effects of the impactor shapes on the low-velocity impact response of the composite panels that produced from different matrix was investigated. Unidirectional E-glass fiber fabrics with an areal density of 300 g/m2 as reinforcement and epoxy matrix were used to produce TS composite. The vacuum-assisted resin infusion molding (VARIM) method was used to manufacture composite panels. The thermoplastic composites were manufactured with E-glass fiber-reinforced polypropylene prepregs. The tensile strength of TS matrix-based composites is higher than TP matrix-based composites that have the same fiber volume fraction. Despite being under the same impact energy, the TP specimens possess higher perforation threshold than TS specimens. The shape of the impactor significantly affected the perforation threshold. Besides, the impact number that caused perforation reduced dramatically in conical impactor. The repeated impact number that caused perforation is 36 for hemispherical (HS) impactor, but it is only 3 for conical impactor for polypropylene matrix-based composite. Moreover, a significant effect of fiber volumetric ratio on impact resistance was observed. The perforation threshold of glass fiber-reinforced polypropylene composites for 40% and 50% fiber volume fraction are 61 and 98 J, respectively. The perforation threshold of TP and TS specimens for HS impactor that has the same stacking sequence is 61 and 55 J, respectively.
AtıfScopus42WoS45OpenAlex44İncele - MakaleYalnız künye2021Scopus SJRQ2High temperature effect on quasi-static and low velocity impact behaviors of advanced composite materials
Karakuzu, Ramazan; Djele, Akim; Dogan, Akar
In this study, the effect of ambient temperatures on the punch shear and low-velocity impact behavior of S2 glass fabric and carbon-kevlar hybrid fabric reinforced epoxy composites was investigated. The quasi-static tests (QST) were performed by using a Universal Shimadzu Tensile Testing Machine with various crosshead speeds. Low-velocity impact (LVI) tests were also carried out by using the CEAST Fractovis Plus impact test machine at different impact energies. Flat-nose impactors with a cylindrical punch diameter of 12.70 mm were mounted to the test machines. Both tests have been carried out at various temperatures. After the experiments, the load-displacement, the absorbed energy-impact energy/crosshead speed and punch shear strength graphs are plotted. From the obtained results it can be said that, in penetration cases of low-velocity impact and quasi-static tests, absorbed energy and punch shear strength values show similar behavior for hybrid carbon-kevlar/epoxy at each temperature except for 80 °C while these values are different from each other for S2 glass/epoxy at all temperatures.
AtıfScopus16WoS14OpenAlex14İncele - MakaleYalnız künye2021Scopus SJRQ1Low-velocity impact, bending, and compression response of carbon fiber/epoxy-based sandwich composites with different types of core materials
Dogan, Akar
This study focuses on the investigation of the effects of different core types on the low velocity impact, three-point bending and out-of-plane compression loading performance of sandwich composites. Three core materials were selected: Balsa wood, PVC foam, and Ayous wood. The facesheets of sandwich composites were produced by woven carbon/epoxy. Balsa and PVC foam are widely used in sandwich composites as core materials. In this study, Ayous wood, which is the lightest tree after Balsa, was used as core material in addition to traditional core materials. Woven carbon fiber fabrics with an areal density 200 g/m2 as reinforcement and epoxy matrix were used to produce the sandwich composite. Vacuum-assisted resin infusion molding method was used to manufacture composite panels. A number of tests under various impact energy levels for three different sandwich composites were conducted with Fractovis Plus impact testing machine in order to investigate the energy absorption capacity of sandwich composites. Maximum contact forces, absorbed energies, and the maximum deflections of sandwich panels were obtained for each impact energy level. Despite having the same facesheets, Ayous core sandwich composites possess a higher perforation threshold than Balsa and PVC foam sandwich composites. The perforation threshold of Balsa, PVC foam, and Ayous sandwich composites are 85, 72, and 170 J, respectively. In addition, the Ayous core sandwich composites have better bending and compression strengths. The bending strength of the Ayous sandwich composite is higher about six times than PVC sandwich composite and about two times than Balsa sandwich composite.
AtıfScopus61WoS56OpenAlex56İncele - MakaleAçık Erişim2018Scopus SJRQ4The effect of hygrothermal aging on the glass and carbon reinforced epoxy composites for different stacking sequences
Dogan, Akar; Arman, Yusuf
The present paper examines the effects of hygrothermal aging on the reinforced epoxy composites. The roles of reinforcement types and stacking sequence on the mechanical properties of composites under hygrothermal aging are investigated. Four different composite materials with different stacking sequence were produced. Unidirectional E-glass and carbon fabrics with an areal density 300 gr/m2 as reinforcement and epoxy as matrix were used. Composites were manufactured using vacuum-assisted resin infusion molding. In order to determine the mechanical properties of the composites, specimens were prepared according to the ASTM standards. The aging process was carried out in climatic test cabin at a temperature of 90oC and a humidity of 90%. As a result of the tests, while the tensile strength of the glass reinforced composites decreased with aging time, no significant change was observed for carbon and hybrid composites. On the other hand, the tensile strength decreased in the transverse direction for all types of composites. XPS analysis was used to understand the distribution of atoms on the surface of specimens.
AtıfScopus22WoS19OpenAlex23İncele