Sürdürülebilir Kalkınma Amaçları

• 6
• 5
• 3

• MakaleAçık Erişim2026Scopus SJRQ1/r/munzur/1361
  Comparative effects of La2O3 and Sm2O3 on structural and radiation shielding properties of WO3 enriched borate glassy-ceramics

  Taşgın, Yahya; Yılmaz, Demet; Kanca, M. Sait; Yayla, Nihal; Kök, Mediha; Güler, Ömer

  This research comprehensively investigates the impact of incorporating rare earth oxides ‑samarium oxide (Sm2O3) and lanthanum oxide (La2O3)- into a borate glassy-ceramic system enriched with tungsten oxide (WO3), with a focus on both structural characteristics and radiation shielding performance. SEM-EDS, elemental mapping, and XRD analyses conducted on the synthesized glassy-ceramic samples revealed that the incorporated rare earth oxides, Sm2O3 and La2O3, were uniformly distributed throughout the glassy-ceramic matrix. The results also confirmed that the glassy-ceramic retained its inherently amorphous structure. Moreover, the nominal doping levels of the rare earth elements were found to be in agreement with both the qualitative and quantitative results obtained from EDS measurements. Also, the gamma ray shielding parameters of synthesized glassy-ceramic samples were measured in absorption geometry with Am-241, Ba-133 and Ra-226 radioactive sources. The neutron shielding parameters were theoretically calculated. The 241Am-Be fast neutron source was used to measure the equivalent dose of neutron absorption. At an incident photon energy of 74.8 keV, the mass attenuation coefficient of the tungsten oxide–enriched borate glassy-ceramic exhibited a remarkable improvement—rising by 17.98 % with the addition of 3 wt% Sm2O3 and by 11.58 % with the addition of 3 wt% La2O3. Notably, the N4 sample demonstrated a significant reduction in neutron-equivalent dose rate, reaching 19.80 % (μSv/h). The lead equivalent thicknesses (Pbeq) calculated at 356 keV were 0.02397 cmPb for N0, 0.0391 cmPb for N1, 0.0403 cmPb for N4, and 0.0389 cmPb for N7. When benchmarked against the undoped N0 sample, the N4 and N7 compositions exhibited reductions in Pbeq values by approximately 68 % and 62 %, respectively, indicating a marked improvement in gamma shielding efficiency. Among all tested formulations, the Sm2O3-doped variant demonstrated superior gamma-ray attenuation capability relative to the La2O3-doped glassy-ceramic. Furthermore, the N4 sample achieved an impressive thermal neutron attenuation rate of 96.46 %, underscoring its strong potential as an effective dual-purpose shielding material against both thermal neutrons and ionizing gamma radiation.

  AtıfScopus1

  İncele
• MakaleYalnız künye2026Scopus SJRQ1/r/munzur/1187
  Effect of Ni–Co–Cr additions on the microstructural and magnetic field–induced radiation shielding behavior of Fe–Si–B alloys

  Taşgın, Yahya; Taşar, Fatih

  Fe–Si–B–based amorphous metallic glasses were synthesized via powder metallurgy and arc melting, followed by alloying with 10 wt% Ni, Co, or Cr. The alloys were examined in both as-cast and heat-treated conditions to assess the combined influence of composition, thermal relaxation, and magnetic processing on their mechanical and radiation-shielding properties. Microstructural characterizations (XRD, SEM, EDS) confirmed homogeneous alloying and the presence of Fe2B, Fe0.91Si0.09, and Ni/Co/Cr-boride phases. After alloying and heat treatment, the average Vickers hardness increased from 313 HV (base Fe-Si-B) to 480 HV. All synthesized samples were exposed to a 1 T magnetic field, and their gamma-ray attenuation behavior was subsequently evaluated using a Ba-133 source (80.99–383.85 keV). After magnetic exposure, the linear attenuation coefficient (LAC) increased by ≈ 3–4% for Co-doped alloys, ≈ 2% for Ni-doped and base Fe–Si–B alloys, and < 0.5% for Cr-doped alloys, accompanied by a corresponding reduction in half-value layer (HVL) from 1.86 cm to 1.79 cm. The fast-neutron removal cross-section (ΣR) also exhibited a modest rise (≈2%). These enhancements are attributed to field-induced microstructural relaxation, including domain alignment, internal-stress reduction, and partial free-volume collapse, which subtly modify the local electron-density distribution without altering the bulk composition. Overall, the findings demonstrate that Ni–Co–Cr alloying, combined with controlled magnetic-field exposure, offers an effective and non-destructive route to enhance both the mechanical durability and γ-ray/fast-neutron shielding performance of Fe-based amorphous alloys, highlighting their potential for magnetically tunable protective coatings and advanced smart-shielding applications. In some applications, both the magnetic properties and radiation shielding properties of the material used are important. This study investigates the effects of Ni, Co, and Cr on the magnetic properties of the Fe-Si-B alloy, while also demonstrating changes in radiation shielding properties.

  AtıfScopus1·WoS1·OpenAlex1

  İncele
• MakaleAçık Erişim2026Scopus SJRQ1/r/munzur/1177
  Radiation shielding performance of (SmEuYbLaEr)2TaO4 high-entropy oxide reinforced Cu matrix composites

  Taşgın, Yahya; Yılmaz, Demet; Kanca, M. Sait; Kök, Mediha; Yayla, Nihal; Güler, Ömer

  High-entropy oxides (HEOs) containing rare earth elements are attracting increasing interest due to their thermal stability and potential for use in radiation shielding applications. In this study, the high-entropy oxide (SmEuYbLaEr)2TaO4 was synthesized via mechanical alloying (MA) followed by calcination and incorporated into a Cu matrix at different reinforcement levels to produce volumetric composites. Structural, thermal, and microstructural analyses confirmed the successful formation of a stable HEO phase and its effective dispersion within the Cu matrix. The radiation shielding performance of the composites was experimentally evaluated over a wide range of photon energies using standard gamma-ray sources. The results showed that shielding performance depends largely on both photon energy and HEO content. Increasing the HEO concentration significantly reduced the half-value layer (HVL) while substantially increasing the mass attenuation coefficient (MAC) and radiation protection efficiency (RPE), particularly in the low- and medium-energy regions where the photoelectric effect is dominant. Among the materials studied, the Cu composite containing 20 wt% HEO exhibited the best overall shielding performance. These results demonstrate that (SmEuYbLaEr)2TaO4 is an effective additive for improving the radiation shielding capability of Cu-based composites and highlight its potential for advanced radiation protection applications.

  AtıfScopus1·OpenAlex1

  İncele
• MakaleAçık Erişim2026Scopus SJRQ2/r/munzur/1068
  Investigation of the Mechanical and Metallographic Effects of Adding 2-3% Al-Ti-Mo Elements to High-Entropy CoCrFeNi Alloys

  Dilek, İlhan; Taşgın, Yahya; Kanca, Muhammed Sait; Kök, Mediha; Güler, Ömer

  Recently, high-entropy alloys (HEAs) have attracted significant attention due to their unique multicomponent composition and exceptional mechanical properties, such as high wear and corrosion resistance, making them superior to conventional alloys for advanced engineering applications. The effects of Al, Ti, and Mo addition on the microstructural and mechanical properties of CoCrFeNi-based HEAs were investigated. The alloys were produced via powder metallurgy and vacuum arc melting, with the addition of 2 and 3% Al, Ti, and Mo, respectively. Scanning electron microscopy (SEM), energy-dispersive x-ray spectroscopy (EDS), and x-ray diffraction (XRD) were used to perform microstructural characterization, while microhardness and wear tests were used to evaluate mechanical performance. The addition of Al and Ti enhanced the face-centered cubic phase stability and increased the hardness by improving the lattice structure. In contrast, the addition of Mo contributed to solid solution and precipitation hardening, resulting in a simpler microstructure and superior tribological performance. Among all compositions, the alloy with 3% Mo addition exhibited the highest hardness value (≈ 233.8 HV) and the lowest mass loss (4.3 mg) was observed, indicating a significant improvement in the wear resistance and mechanical strength. In conclusion, the addition of Ti and Mo to CoCrFeNi HEAs promotes solid solution, precipitation, and grain boundary hardening mechanisms, thereby enhancing microstructural integrity, hardness, and wear resistance. These findings suggest that such alloys are promising candidates for use as next-generation structural and tribological materials under demanding operational conditions.

  İncele
• MakaleAçık Erişim2026Scopus SJRQ1/r/munzur/909
  Comparative and systematically analysis of the effects of single and high-entropy rare earth oxide additives on the some physical properties and radiation shielding properties of copper composites

  Kanca, Muhammed Sait; Yılmaz, Demet; Tasgın, Yahya; Kök, Mediha; Güler, Seval Hale

  In this study, the effects of rare earth oxides (Gd₂O₃, La₂O₃, Eu₂O₃, Pr₂O₃, Dy₂O₃, and Y₂O₃) and high-entropy oxide (GdLaEuPrDyY)₂O₃ additives on the structural, mechanical, and radiation shielding properties of copper matrix composites were investigated. XRD and SEM-EDS analyses showed that the high-entropy oxide successfully formed in a single-phase bixbyite structure after mechanical alloying and was homogeneously distributed within the copper matrix. The rare earth oxide additive significantly reduced the crystal grain size of the Cu matrix and improved its mechanical properties. Specifically, the microhardness value reached 68.3 Hv in the composite with 20% high-entropy oxide additive, representing an increase of approximately 111% compared to pure copper (32.3 Hv). Gamma shielding results showed that the rare earth oxide additive significantly increased the photon attenuation capacity. Specifically, at 242 keV energy, the Dy₂O₃ additive increased the MAC value from 0.141 cm²/g to 0.246 cm²/g, providing a 74.5% improvement. The most important result is that the composite with 20% high-entropy oxide additive showed the highest shielding performance, achieving a MAC value of 0.278 cm²/g, which is significantly superior to pure copper. Furthermore, this composite exhibited the lowest HVL and MFP values, demonstrating the highest photon shielding efficiency. Neutron shielding analyses revealed that Gd₂O₃ and high-entropy oxide additives, in particular, increased thermal neutron attenuation performance to approximately 100%. These results demonstrate that high-entropy oxide additives provide a stronger impact compared to single oxide additives, offering superior performance in both gamma and neutron shielding. Consequently, copper composites doped with (GdLaEuPrDyY)₂O₃ stand out as promising alternative shielding materials for nuclear facilities, radiation protection systems, and advanced engineering applications due to their high shielding efficiency, improved mechanical properties, and non-toxic composition.

  AtıfScopus1·OpenAlex1

  İncele
• MakaleAçık Erişim2026Scopus SJRQ1/r/munzur/702
  Structural and radiation shielding properties of high-entropy rare-earth oxide-doped borosilicate glass

  Güler, Ömer; Yılmaz, Demet; Kanca, Muhammed Sait; Kök, Mediha; Taşgın, Yahya

  In this study, the incorporation of a high-entropy rare-earth oxide, (GdLaEuPrDyY)2O3 (RE-HEO), into a borosilicate glass matrix was investigated with the aim of improving radiation shielding performance while preserving the structural integrity of the glass. The RE-HEO was first synthesized by high-energy mechanical alloying and then introduced into the glass system at concentrations ranging from 0 to 8 wt% using a conventional melt-quenching process. The structural and microstructural properties of the prepared samples were examined using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy combined with energy-dispersive spectroscopy (SEM–EDS). The analyses confirmed that the amorphous nature of the borosilicate glass was maintained and that the rare-earth elements were homogeneously distributed within the matrix. The radiation shielding performance was evaluated experimentally using Am-241, Ba-133, and Ra-226 gamma sources, and supported by theoretical calculations of key parameters including mass attenuation coefficient (MAC), half-value layer (HVL), mean free path (MFP), effective atomic number (Zeff), exposure buildup factor (EBF), and fast neutron removal cross-section (ΣR). The results showed that increasing RE-HEO content leads to a noticeable improvement in gamma-ray attenuation. In particular, the sample containing 8 wt% RE-HEO exhibited a MAC value of 0.131 cm2/g and an HVL of 2.03 cm at 356 keV, indicating shielding performance comparable to that of conventional lead-containing glasses. In addition, irradiation tests performed using a Co-60 gamma source revealed that the amorphous structure remains stable after exposure. Overall, the findings suggest that RE-HEO-doped borosilicate glass can be considered a promising lead-free alternative for radiation shielding applications.

  AtıfScopus1·WoS1·OpenAlex1

  İncele
• MakaleAçık Erişim2026Scopus SJRQ2/r/munzur/700
  Radiation shielding performance of CeO2-reinforced ternary nanocomposites based on biodegradable polymers and waste-derived polystyrene

  Pekdemir, Mustafa Ersin; Yilmaz, Demet; Selçuk Pekdemir, Sibel; Gülhan, Aleyna; Yalçin Kuzu, Serpil; Altun, Sedanur; Taşgin, Yahya

  The development of sustainable polymer-based materials for radiation shielding has attracted increasing interest, particularly for lightweight and flexible applications. In this study, ternary nanocomposites based on poly (hydroxyalkanoate) (PHA), poly (ε-caprolactone) (PCL), and polystyrene (PS) were prepared and reinforced with cerium oxide (CeO2) nanoparticles (5–15 wt%) to enhance radiation shielding performance. Structural characterization confirmed the preservation of polymer chemical structures and the successful incorporation of crystalline CeO2, while SEM observations revealed a relatively homogeneous nanoparticle dispersion within the ternary matrix, particularly at intermediate filler loadings. Thermal analysis demonstrated enhanced thermal stability with increasing CeO2 content, as evidenced by an increase in residual mass from 0.42% for the neat blend to 11.21% for the nanocomposite containing 15 wt% CeO2, along with a shift of degradation onset temperatures toward higher values. Photon shielding performance was experimentally evaluated in the energy range of 13.37–59.54 keV. The incorporation of 15 wt% CeO2 increased the mass attenuation coefficient (MAC) from 1.277 to 12.366 cm2 g−1 at 13.37 keV, corresponding to an approximately ninefold enhancement, while significantly reducing the half-value layer (HVL) and mean free path (MFP). Neutron shielding analysis showed a slight decrease in thermal neutron attenuation due to hydrogen dilution within the polymer matrix, whereas fast neutron attenuation and neutron removal cross sections exhibited only minor variations; the fast neutron removal cross section increased modestly from 0.1014 to 0.1047 cm−1 with 15 wt% CeO2 addition. Overall, the results highlight clear structure–property–performance relationships in CeO2-reinforced PHA/PCL/PS nanocomposites, demonstrating their potential as lightweight radiation shielding materials for low energy protection with improved thermal stability and shielding efficiency.

  • 
  AtıfScopus2·OpenAlex1

  İncele
• MakaleAçık Erişim2026Scopus SJRQ1/r/munzur/695
  Investigation of the structural, thermal and radiation shielding properties of (Er0.2Yb0.2Sm0.2La0.2Eu0.2)2Zr2O7 high entropy oxide reinforced tin matrix composite

  Güler, Ömer; Yılmaz, Demet; Kanca, M. Sait; Kök, Mediha; Güler, Seval Hale; Taşgın, Yahya

  This study investigates the structural, thermal, and radiation shielding properties of (Er0.2Yb0.2Sm0.2La0.2Eu0.2)2Zr2O7 high entropy oxide (HEO) reinforced tin (Sn) matrix composites. In the first stage of the study, HEO powders were synthesized by grinding at 350 rpm for 30 h using a solid-state method with mechanical alloying assistance, and then calcining at 1100 °C for 8 h. In the second stage, composites were produced by mixing HEO-reinforced Sn matrix materials containing 1%, 5%, and 10% reinforcement, pelleting them under 200 MPa pressure, and then sintering them at 300 °C for 3 h. In the first stage of the study, (Er0.2Yb0.2Sm0.2La0.2Eu0.2)2Zr2O7 HEO powders were synthesized using a mechanical alloying-assisted solid-state route. In the second stage, HEO-reinforced Sn matrix composites containing 1 wt%, 5 wt%, and 10 wt% reinforcement were produced. The phase formation and crystallographic structure of the synthesized powders and composites were characterized using X-ray diffraction. Thermal behavior and phase stability were investigated by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The thermal analysis results revealed dehydration and structural stabilization processes at intermediate temperatures, while crystallization of the HEO phase was observed at elevated temperatures. In addition, oxidation behavior of the Sn matrix composites was evaluated, showing that the presence of HEO particles significantly suppresses mass gain during high-temperature oxidation, indicating improved thermal stability. Finally, the radiation shielding performance of the samples was experimentally evaluated within the photon energy range of 59.54–609.2 keV using Am-241, Ba-133, and Ra-226 radioactive sources together with a Ultra-Low Energy Germanium (ULEGe) detector. The results demonstrate that the incorporation of HEO particles leads to minor, energy-dependent variations in the radiation attenuation capability of the tin matrix, influenced by the presence of high atomic number rare-earth elements and modified microstructural characteristics. The gamma radiation protection coefficient (RPC) values indicate strong attenuation in the low photon energy region, decreasing to approximately 16–19% at 609.3 keV. Moreover, the measured neutron equivalent dose rates increase from 0.054 µSv/h for pure Sn to 0.285 µSv/h for the Sn–10%HEO composite, indicating that HEO incorporation modifies the neutron interaction behavior of the Sn matrix composites.

  İncele
• MakaleYalnız künye2025Scopus SJRQ2/r/munzur/1441
  The effect of WC addition on CrMnFeCoNi high entropy alloys: crystal-micro structure, hardness and wear behavior

  Taşgın, Yahya; Kanca, M Sait; Kök, Mediha; Anik, Kerem

  High entropy alloys are produced by combining four or more elements in close percentage ratios. Recently, these alloys have become the preferred group due to their superior mechanical and thermal properties. In this study, tungsten carbide (WC) was doped into CrMnFeCoNi alloys at different ratios, and the effects of WC and heat treatment on the doped alloys were investigated. XRD, SEM, and EDS analyses, wear tests, and microhardness measurements were performed on the produced samples to examine their microstructural properties. When comparing the heat-treated samples with WC (3%, 5%, and 10% additions) to the untreated samples, it was found that the average hardness values of the heat-treated samples were higher. Although the grain structures of the samples, as observed through XRD, SEM, and EDS, were preserved, their ratios were altered, and the wear tests revealed that the mass losses of the heat-treated samples increased.

  İncele
• MakaleAçık Erişim2025Scopus SJRQ2/r/munzur/1144
  Investigation of the effect of the metallographic properties of vertical and horizontal cylinders made of ferrochrome with different contents on heat transfer by natural convection

  Kahraman, Gökhan; Taşgın, Yahya

  In this study, ferrochrome materials containing elements with different content ratios were manufactured into six-cylinder specimens, 13 mm in diameter and 16 mm in length, and heated in a furnace up to 500 °C. The heated cylinders were removed and left to cool in vertical and horizontal positions in a 16 °C environment. The temperatures were recorded using thermal cameras at certain intervals while the materials cooled down. The six specimens, whose metallographic differences were identified using SEM and XRD analysis devices, were placed vertically and horizontally, and their heat transfer by natural conviction was noted. In the calculations, each specimen’s Nusselt and Rayleigh numbers were identified based on time and then compared. The fastest cooling among the specimens occurred in the ferrochromium material with 55.93% Cr, 31.11% Fe, 11.56% C, 0.48% Si, 0.83% O, and 0.09% Al compound ratios, both in vertical and horizontal positions. Additionally, since the Nusselt number of the horizontal cylinders remained below one based on their position, their natural convection flows were not initiated. The cooling in the horizontal cylinders occurred via conduction.

  İncele