Munzur ÜniversitesiMunzur ÜniversitesiAçık Erişim Arşivi · RDL Open

Effects of Temperature and Hole Drilling on Adhesively Bonded Single-Lap Joints

MakaleYalnız künyeScopus SJRQ2

Özet

In this study, the load-carrying capacity of a single-lap joint bonded by an adhesive was determined experimentally. Glass fiber-epoxy composite material was chosen as adherends and Loctite (R) 9466 A&B2 was used as adhesive. The vacuum assisted resin infusion method (VARIM) was used to manufacture composites. In this experimental study, the effects of hole drilling and temperature were investigated. Five hole configurations and three temperatures (room temperature, 50 degrees C, and 80 degrees C) were considered. The results show that hole drilling elevate the failure load and when the temperature increases the load-carrying capacity decreases.

Anahtar Kelimeler

Hole drillingLap-shearStress analysisSurface modificationTemperature
RDL Kalıcı Bağlantı (PID)
https://rdlopen.rawdatalibrary.net/r/munzur/4390Resmi atıflarda kullanılan kalıcı adres
İndeks kayıtları
Web of ScienceWeb of Science
Kaydın indeks veri tabanlarındaki sayfası (aktarımda alınan kayıt numarasıyla). Erişim, indeksin kendi koşullarına bağlıdır.
Atıflar
WoS
20
OpenAlex
21
Her kaynağın kendi saydığı toplam atıf; aktarım ve zenginleştirme sırasında alındı.
Tam Kayıt
AlanDeğerDil
dc.contributor.authorArikan, Volkan
dc.contributor.authorDogan, Akar
dc.contributor.authorDogan, Tolga
dc.contributor.authorSabanci, Eray
dc.contributor.authorAl-Shamary, Adel Kadum Jassim
dc.date.accessioned2026-10-28T14:59:15.496638529Z
dc.date.available2026-10-28T14:59:15.496638529Z
dc.date.issued2015
dc.description.abstractIn this study, the load-carrying capacity of a single-lap joint bonded by an adhesive was determined experimentally. Glass fiber-epoxy composite material was chosen as adherends and Loctite (R) 9466 A&B2 was used as adhesive. The vacuum assisted resin infusion method (VARIM) was used to manufacture composites. In this experimental study, the effects of hole drilling and temperature were investigated. Five hole configurations and three temperatures (room temperature, 50 degrees C, and 80 degrees C) were considered. The results show that hole drilling elevate the failure load and when the temperature increases the load-carrying capacity decreases.
dc.identifier.doi10.1080/00218464.2013.874293
dc.identifier.eissn1545-5823
dc.identifier.endpage185
dc.identifier.issn0021-8464
dc.identifier.issue3
dc.identifier.startpage177
dc.identifier.urihttps://rdlopen.rawdatalibrary.net/r/munzur/4390
dc.identifier.volume91
dc.identifier.wosWOS:000342293300003
dc.language.isoen
dc.publisherTAYLOR & FRANCIS LTD
dc.relation.ispartofJOURNAL OF ADHESION
dc.rightsinfo:eu-repo/semantics/closedAccess
dc.subjectHole drilling
dc.subjectLap-shear
dc.subjectStress analysis
dc.subjectSurface modification
dc.subjectTemperature
dc.subject.classificationEngineering, Chemical
dc.subject.classificationMaterials Science, Multidisciplinary
dc.subject.classificationMechanics
dc.subject.classificationEngineering
dc.subject.classificationMaterials Science
dc.subject.otherFAILURE
dc.subject.otherSTRENGTH
dc.subject.otherBEHAVIOR
dc.titleEffects of Temperature and Hole Drilling on Adhesively Bonded Single-Lap Joints
dc.typeArticle
rdl.citation.openalex21
rdl.citation.wos20
rdl.oa.statusclosed
rdl.scopus.quartileQ2
rdl.source.indexWOS
rdl.wos.indexScience Citation Index Expanded (SCI-EXPANDED)