Sürdürülebilir Kalkınma Amaçları

• 1
• 1
• 1

• MakaleAçık Erişim2026Scopus SJRQ1/r/munzur/1119
  Failure of a Code-Compliant Reinforced Concrete Building: Damage Patterns and Nonlinear Seismic Response

  Onat, Onur; Karaşin, İbrahim Baran; Yön, Burak; Varolgüneş, Sadık; Öncü, Mehmet Emin; Uslu, Ali

  This study investigates the seismic performance limitations of a newly constructed reinforced concrete building that collapsed during the 6 February 2023 Kahramanmaraş–Elbistan earthquake despite formal compliance with current seismic design requirements. Beyond the specific earthquake event, the study addresses a broader scientific problem: the limited understanding of the relationship between observed damage mechanisms and nonlinear dynamic response in mid-rise reinforced concrete buildings. The first part classifies recurring structural and non-structural damage patterns identified in newly constructed RC residences. The second part presents a nonlinear fiber-based static and dynamic analysis of a collapsed mid-rise building. Nonlinear dynamic analyses were conducted using ground motion records scaled to match the site-specific elastic design spectrum defined by TBDY 2018, corresponding to predefined seismic performance levels rather than an incremental dynamic analysis framework. The results indicate that an extremely low shear wall–to–floor area ratio (0.0357%) combined with asymmetric vertical element distribution significantly amplified torsional response and local shear demands. Nonlinear dynamic analyses showed that critical shear walls exceeded Collapse Prevention limits under DD2-level excitation, while system-level shear contribution limits remained within code-defined thresholds. Dynamic base shear demand corresponded to approximately 30% of the maximum nonlinear capacity obtained from pushover analysis, indicating that localized member failure rather than global strength deficiency governed the collapse mechanism. The analytically identified critical members were consistent with the observed collapse configuration, particularly at the soft ground story. The findings demonstrate that prescriptive code compliance alone may not ensure satisfactory seismic performance when structural irregularities, torsional amplification, and detailing deficiencies coexist. The results are consistent with damage patterns reported in other recent destructive earthquakes and contribute to improving the understanding of collapse mechanisms in code-compliant RC buildings.

  • 
  AtıfScopus4·OpenAlex7

  İncele
• MakaleAçık Erişim2026Scopus SJRQ1/r/munzur/989
  Freeze–Thaw Performance and Microstructural Stability of Alkali-Activated Slag Mortars Incorporating Mussel Shell Waste

  Şahin Yön, Merve

  This study investigates the use of mussel shells (MSs), a biogenic by-product of the food industry, as a partial replacement for ground granulated blast furnace slag (GBFS) in alkali-activated mortars. Given their high CaCO3 content, MSs represent a sustainable secondary raw material that reduces both waste disposal burden and reliance on natural resources, while offering a low-carbon alternative to conventional cement-based binders. Alkali-activated mussel shell/slag mortars (AAMSs) were produced with MS replacement ratios of 0%, 5%, 10%, 15%, and 20% by mass of GBFS. Sodium hydroxide (NaOH) and sodium silicate (Na2SiO3) were used as alkaline activators. Fresh specimens were cured at 60 °C for 48 h. The experimental program included workability, compressive and flexural strength, water absorption, porosity, density, capillarity, ultrasonic pulse velocity (UPV), and freeze–thaw (F-T) resistance tests. Increasing MS content slightly reduced flowability and mechanical strength, while increasing water absorption, porosity, and capillarity. The M0 series achieved the highest 28-day compressive strength (54.06 MPa), while M15 exhibited the highest flexural strength (5.23 MPa). Following F-T cycling, the 5% and 10% MS series demonstrated the best compressive strength (30 MPa). The 10% MS exhibits a relatively balanced overall performance, providing the best balance between mechanical performance, F-T resistance, and microstructural stability, as confirmed by scanning electron microscopy (SEM)/energy-dispersive X-ray spectroscopy (EDS) analyses showing elevated Ca/Si ratios and the formation of Ca-rich crystalline phases.

  • 
  İncele
• MakaleAçık Erişim2025Scopus SJRQ1/r/munzur/1268
  Spring-Based Soil–Structure Interaction Modeling of Pile–Abutment Joints in Short-Span Integral Abutment Bridges with LR and RSM

  Polat, Erkan; Göçmen Polat, Elifcan

  Integral abutment bridges (IABs) are increasingly adopted in transportation infrastructure due to their durability, reduced maintenance needs, and cost-effectiveness compared to conventional bridges. However, their reliable performance under live loads is strongly influenced by the nonlinear soil–structure interaction (SSI) at the pile–abutment joint, which remains challenging to quantify using conventional analysis methods. This study develops simplified spring-based models to capture the SSI behavior of pile–abutment joints in short-span IABs. Predictive equations for joint rotation, deflection, moment, and shear are formulated using Linear Regression (LR) and Response Surface Methodology (RSM). Unlike prior studies relying solely on FEM or traditional p–y curves, the novelty of this work lies in deriving regression-based spring constants calibrated against FEM analyses, which can be directly implemented in standard structural software. This approach significantly reduces computational demands while maintaining predictive accuracy, enabling efficient assessment of pile contributions and global bridge response. Validation against finite element method (FEM) results confirms the reliability of the simplified models, with RSM outperforming LR in representing nonlinear parameter interactions.

  • 
  AtıfScopus2·WoS2·OpenAlex3

  İncele