Ali, Shahbaz; Nadeem, Sohail; Akkurt, Nevzat; Ali Ghazwani, Hassan; Eldin, Sayed M.

Introduction: Flow dynamics due to the peristaltic pumping has been the topic of great interest for the researchers. But numerical and analytical analyses for the peristaltic motion are limited where flow domain is deformed real-time. Research on peristalsis has a limitation where theoretical aspects of walls motion are considered, neglecting the real time deformation of the walls. Objectives: This paper aims to propose a more reliable and accurate numerical methodology for peristaltic motions to address the above-mentioned challenge. Stream traces, velocities, and pressure drops along the tube is to be visualized more accurately. Methods: In present study a finite volume based dynamic mesh motion method is adopted to analyze the peristaltic motion of a non-Newtonian Quemada fluid in an axisymmetric channel. The walls and interior domain of the channel is dynamically deformed for a sinusoidal wave traveling on boundary. Results: Simulation of unsteady flow behavior for time t=0s to 2s and amplitude ratio Φ=0.2,0.4,and0.6. predicts fluid trapping phenomenon. Rotation of fluid particles is more prominent for higher amplitude ratios. Pressure gradient increases with increasing amplitude ratios. Conclusion: A novel dynamic mesh method is proposed for peristaltic pumping. It provides more accurate and more physical results for stream traces; pressure drops and velocities along the tube. A limited case of the study validates the theoretical and analytical results already presented in literature; hence the method is reliable.

AtıfScopus10·OpenAlex12

İncele

Nadeem, Sohail; Ali, Shahbaz; Akkurt, Nevzat; Bechir Ben Hamida, Mohamed; Almutairi, Shahah; Ghazwani, Hassan Ali; Eldin, Sayed M.; Khan, Zareen A.; Al-Shafay, A.S.

The authors regards, In the original article, in Ref. [16], the citation was incorrectly stated as: H. Liu et al., 3D printing of artificial blood vessel: study on multi-parameter optimization design for vascular molding effect in alginate and gelatin, Micromachines (2017) 8. However, upon thorough review and verification, the authors have discovered that the correct citation should be as follows: V. Carvalho, N. Rodrigues, R. Ribeiro, P.F. Costa, R.A. Lima, S.F.C.F. Teixeira, 3D printed biomodels for flow visualization in stenotic vessels: An experimental and numerical study, Micromachines, vol. 11, no. 6, doi: 10.3390/mi11060549. The authors deeply apologize for this oversight and any confusion it may have caused to the readers and the scholarly community. It is crucial to ensure the accuracy and integrity of their citations, and they sincerely regret any inconvenience this may have caused.

İncele

Singupuram, Raghav; Alam, Tabish; Ali, Masood Ashraf; Shaik, Saboor; Gupta, Naveen Kumar; Akkurt, Nevzat; Kumar, Mukesh; Eldin, Sayed M.; Dobrotă, Dan

Electronic components used in a variety of applications, such as electronic devices, computers, automobiles, medical equipment, telecommunications, etc., can be effectively cooled using microchannel heat sinks (MHS). In this paper, a novel design of an MHS is presented, which can manage the heat load (dissipate the excess heat) and maintain the temperature of the MHS in the safe range. The passage of the MHS was modified with circular extruding ribs on the side wall of the passage. This technique in MHS was inspired by the study of heat transfer enhancement in heat exchangers. The effects of the sector angle of the circular protruding ribs ranging from 45° to 80° were studied in laminar flow (Re = 100–900). It was found that the maximum Nusselt number in the range of 7.26–64.11 was observed at sector angles of circular protrusion ribs of 80°. Also, the values of thermohydraulic performance parameter (THPP) are greater than one, which shows that the application of the proposed design for thermal management of MHS is reasonable and effective.

AtıfScopus41·OpenAlex43

İncele

Shamshuddin, MD.; Raizah, Zehba; Akkurt, Nevzat; Patil, Vishwambhar S.; Eldin, Sayed M.

The effect of multiple slip boundary conditions is one more important physical parameter on the flow investigation and have been studied in this analysis. Further, the effect of Ohmic heating and varying chemical reaction on non-Newtonian Prandtl hybrid nanofluid with water based nanofluids to an extending of leading edge was also investigated to this current analysis. An inclined magnetic field is introduced to fluid flow to regulate the fluid stream. Hybrid nanomaterial is synthesized by the dispersion of Cu and Cofe2O4 nanoparticles in Prandtl fluid. All chemical science specifications of nanofluid are measured as constant. Due to the nanofluid particles motion, the fluid concentration is inspected underneath chemical implications. A mathematical model is developed by assuming the flow as incompressible and purely cartesian coordinate system and appropriate non-dimensional variables are introduced for problem simplifications and dimensional analysis. The scheme for semi analytical study named Homotopy Analysis Method (HAM) is implied to get solutions to the equations. The procedure is then displayed pictorially where fluid velocity, temperature and concertation against various pertinent parameters are examined. It was found that, the Concentration field profiles have been shown to deteriorate because molecule diffusivity reduces as the chemical reaction parameter rises in both cases. In order to maintain thermal balance management in tiny heat density equipment and gadgets, current research may also be helpful in enhancing the thermal efficiency of heat exchangers.

AtıfScopus41·WoS38·OpenAlex44

İncele

Ullah, Zia; Akkurt, Nevzat; Alrihieli, Haifaa F.; Eldin, Sayed M.; Alqahtani, Aisha M.; Hussanan, Abid; Ashraf, Muhammad; Jabeen, Mah

The heat transmission properties along the non-magnetized geometries have been numerically obtainedby various researchers. These mechanisms are less interesting in engineering and industrial processes because of excessive heating. According to current studies, the surface is magnetized and the fluid is electrically conductive, which helps to lessen excessive surface heating. The main objective of the current analysis is to numerically compute the temperature-dependent density effect on magnetohydrodynamic convective heat-transfer phenomena of electrical-conductive fluid flow along the vertical magnetized and heated plate placed in a thermally stratified medium. For the purpose of numerical analysis, the theoretical process governing heat and magnetic intensity along a vertical magnetic plate is examined. By using suitable and well-known similarity transformations for integration, the non-linear coupled PDEs for the aforementioned electrical-conductive fluid flow mechanism are changed and subsequently converted into non-similar formulation. The Keller Box method is used to numerically integrate the final non-similar equations. The MATLAB software program plots the transformed algebraic equations graphically and quantitatively. The behavior of the physical quantities such asvelocity graph, magnetic field graph, and temperature plot along with their slopes that arerate of skin friction, the rate of heat transfer, and the rate of magnetic intensity for different parameters included in the flow model. The novelty of the current work is to compute the magneto-thermo analysis of electrically conducting flow along the vertical symmetric heated plate. First, we secure the numerical solution for steady part and then these results are used to find skin friction, heat transfer, and magnetic intensity. In the current work, the fluid becomes electrically conducing due to a magnetized surface which insulates heat during the mechanism and reduces the excessive heating. The results are excellent and accurate because they are satisfied by its given boundary conditions. Additionally, the current problems have a big impact on the production of polymer materials, glass fiber, petroleum, plastic films, polymer sheets, heat exchangers, catalytic reactors, and electronic devices.

AtıfScopus20·OpenAlex18

İncele

Hussain, Azad; Arsaln, Muhammad; Rehman, Aysha; Alharbi, Fahad M.; Akkurt, Nevzat; Eldin, Sayed M.; Althobaiti, Saad

The unsteady compressible steam laminar flow associated with heat transfer in fluids in a squared cylinder is examined in this work. The current challenge was created utilizing the CFD approach. The laminar flow is chosen with a low Mach number. With the geometric wall, the flow has a no-slip condition. The pressure on the flow is kept at 0 pas, and the temperature in the flow regime is 305.13. A 0.5 m/s velocity is used to start the flow. With the use of graphics, the effects of time on velocity and pressure distributions are discussed. Different outcomes are also mentioned, such as drag coefficients, lift coefficients, and heat distributions. The velocity drops from 2.5 to 1.6 m/s at t = 7 s in the absence of anybody's force and temperature 305.13 K. Pressure increases from 0.00098 to 0.001 Pas in the flow interval of 10 s. Surface temperature increases from 360 to 375 K in time intervals of 10 s keeping pressure constant. And contour temperature increases from 371.56 to 374.2 K in time intervals of 10 s keeping the pressure constant. This information provides us with caution about the emission of steam from the chimneys of furnaces. It implies that when steam flows from a cylindrical geometry like chimneys of furnaces it heats the upper inner and outer parts which may destroy the material. So for safety, that emission should be taken for a short interval of time otherwise it will result in a havoc process. The lift coefficient remains constant and the drag coefficient increases from 0.0005 to 0.065. Under that condition, fluid has to face more resistance. To overcome that difficulty fluid should be provided with high velocity to continue it for a long time. The technique used to solve modeled problems is the Backward Difference Formula.

İncele

Khan, Umair; Zaib, Aurang; Ishak, Anuar; Alotaibi, Abeer M.; Eldin, Sayed M.; Akkurt, Nevzat; Waini, Iskandar; Madhukesh, Javali Kotresh

The utilization of hybrid nanofluids (HNs) to boost heat transfer is a promising area of study, and thus, numerous scientists, researchers, and academics have voiced their admiration and interest in this area. One of the main functions of nanofluids is their dynamic role in cooling small electrical devices such as microchips and associated gadgets. The major goal of this study is to perform an analysis of the buoyancy flow of a shrinking/stretching sheet, whilst considering the fascinating and practical uses of hybrid nanofluids. The influence of a nonlinear heat source/sink induced by a micropolar fluid is also inspected. Water-based alumina and copper nanoparticles are utilized to calculate the fine points of the fluid flow and the features of heat transfer. The governing equations are framed with acceptable assumptions and the required similarity transformations are used to turn the set of partial differential equations into ordinary differential equations. The bvp4c technique is used to solve the simplified equations. Dual solutions are presented for certain values of stretching/shrinking parameters as well as the mixed convective parameter. In addition, the shear stress coefficient in the first-branch solution (FBS) escalates and decelerates for the second-branch solution (SBS) with the superior impact of the magnetic parameter, the mass transpiration parameter, and the solid nanoparticles volume fraction, while the contrary behavior is seen in both (FB and SB) solutions for the larger values of the material parameter.

AtıfScopus22·OpenAlex27

İncele

Raza, Ali; Khan, Umair; Eldin, Sayed M.; Alotaibi, Abeer M.; Elattar, Samia; Prasannakumara, Ballajja C.; Akkurt, Nevzat; Abed, Ahmed M.

Given the importance and use of electrically conducted nanofluids, this work aims to examine an engine-oil-based nanofluid including various nanoparticles. In the current study, a fractional model for inspecting the thermal aspect of a Brinkman-type nanofluid, composed of (molybdenum disulfide (MOS2) and graphene oxide (GO) nanoparticles flows on an oscillating infinite inclined plate, which characterizes an asymmetrical fluid flow, heat, and mass transfer. Furthermore, the Newtonian heating effect, magnetic field, and slip boundary conditions were taken into account. The objectives for implementing the Prabhakar-like fractional model are justified because this fractional algorithm has contemporary definitions with no singularity restrictions. Furthermore, the guided fractional model was solved using the Laplace transform and several inverse methods. The obtained symmetrical solutions have been visually analyzed to investigate the physics of several relevant flow parameters on the governed equations. Some exceptional cases for the momentum field are compiled to see the physical analysis of the flowing fluid symmetry. The results show that the thermal enhancement can be progressively improved with the interaction of the molybdenum disulfide-engine oil-based nanofluid suspension, rather than with the graphene oxide mixed nanoparticle fluid. Furthermore, the temperature and momentum profiles enhance due to the factional parameters for molybdenum disulfide and the graphene oxide-engine oil-based nanofluid suspension. This study’s graphical and numerical comparison with the existing literature has shown a very close resemblance with the present work, which provides confidence that the unavailable results are accurate. The results show that an increase improved the heat transmission in the solid nanoparticle volume fractions. In addition, the increment in the mass and heat transfer was analyzed in the numerical evaluation, while the shear stress was enhanced with the enhancement in the Prabhakar fractional parameter α.

AtıfScopus15·OpenAlex15

İncele

Hussain, Azad; Akkurt, Nevzat; Rehman, Aysha; Alrihieli, Haifaa F.; Alharbi, Fahad M.; Abdussattar, Aishah; Eldin, Sayed M.

The fundamental purpose of this research is to elaborate on slip boundary conditions and the flow of three-dimensional, stable, incompressible, rotating movements of nanoparticles lying across a stretchable sheet. The mathematical model for fluid flow is created using the assumptions stated above. The partial differentials are produced after utilizing boundary layer estimates. The partial differential governing equations are reduced into three coupled ordinary differential equations by using similarity transformations. After, applying transformations the system is solved numerically. Numerical results are approved with the help of the MATLAB bvp4c algorithm. The analysis shows that velocity and temperature are strongly dependent on essential parameters like stretching ratio, velocity slip, rotation, thermal slip parameter, and Prandtl number. Numerical values of distinct parameters on heat flux and skin friction factors are shown in a tabulated form. Partial velocity and thermal slip are applied to the temperature surface. The comparison among the nano-sized particles copper oxide and silver with water base nanofluid affecting velocity and temperature fields are used for analysis. Moreover, the Graphical depiction designates that the velocity and temperature spreading of the thermal slip parameter is increasing. It is observed that Ag-water is the best heat carrier as compared to CuO-water nanofluid.

AtıfScopus15·OpenAlex20

İncele