Yayınlar
Koleksiyondaki öğeler
- MakaleYalnız künye2025Scopus SJRQ1Mechanical, durability and microstructure properties of eco-friendly self-compacting mortars with addition of volcanic scoria, silica fume and boron waste as cement replacement
Şahin Yön, Merve
The objective of this experimental study is to investigate the mechanical and durability performances of self-compacting mortars containing industrial waste and natural stone to develop an environmentally friendly mortar. Binary series of boron waste (B), silica fume (S) and volcanic scoria (V) were formed by substituting up to 95 % by weight with Portland cement, and ternary series were formed by substituting up to 80 % by weight with Portland cement. A total of 14 mixtures and one reference mixture (R) were improved for the purpose of investigating the workability, mechanical strength and durability properties of self-compacting mortar with different binder compositions. Samples of 40x40x160 mm were produced to evaluate mechanical properties and freeze-thaw effect, 100x100x100 mm for abrasion testing and 50x50x50 mm to determine physical properties. Additionally, SEM/EDS and XRD analyses were performed to determine the microstructural characteristics of the mixtures formed. The test results demonstrated that the sole replacement of boron waste with Portland cement resulted in enhanced fluidity. Nonetheless, the 90-day compressive strengths of the S10V20 and B5S10V5 mixtures exhibited increases of 7.47 % and 5.57 %, respectively, relative to the reference, whilst the B15 series saw a 52.5 % reduction, marking the lowest 90-day compressive strength compared to the reference sample. When the freeze-thaw effect was assessed after 136 cycles, the compressive strength diminished by 8.57 %, 13.1 %, 4.13 %, 7.28 %, 6.22 %, 24.77 %, and 48.1 % in the R, B5, V5, V10, V15, B5S10V5, B5S10V10, and B5S10V15 samples, respectively. Among the samples subjected to abrasion tests, a loss of 6.5 per thousand occurred in the mass of the reference sample at the end of 6 minutes, while a loss of 11 per thousand occurred in the binary mixture containing 5 % B, which had the highest abrasion.
AtıfScopus16WoS14OpenAlex16
İncele - MakaleYalnız künye2026Scopus SJRQ2Kinetic investigation on the recovery of copper and cobalt from sulphuric acid plant electrofilter dust
Erust, Ceren
Several waste dusts collecting equipment options are available for air pollution control in plants, the most commonly used being the electrofilter. Industrial wastes such as electrofilter dust are evaluated as a secondary resource owing to their critical metal contents. In this work, the results of studies on the extraction of cobalt and copper from electrofilter dust generated in sulphuric acid production plants are presented. The chemical and mineralogical compositions of the dust were investigated using instrumental analytical methods. The electrofilter dust consists of the main phases of haematite, quartz, and anhydrite. Also, electrofilter dust contains 1.43% copper and 0.28% cobalt. It was found that the process of copper and cobalt dissolution is characterized by chemical kinetics. When the acid leaching was applied in 1 M sulphuric acid in the presence of 0.05 M hydrogen peroxide, with the temperature 80°C and 2 h of leaching time, stirring rate of 200 rpm and liquid to solid ratio 20/1 v/w, cobalt and copper extraction achieved 88% and 98% respectively. As a result of studying the kinetics of acid leaching with sulphuric acid in the presence of oxidant hydrogen peroxide, activation energy and the type of reaction to chemical controlled model were determined.
AtıfScopus2WoS2OpenAlex1İncele - MakaleAçık Erişim2025Scopus SJRQ2Effects of ZrN and DLC coatings on morphostructural, corrosion, cell viability, and antibacterial properties of Ti6Al4V scaffolds
Aslan, Naim; Aksakal, Bünyamin; Cihangir, Salih; Fidan, Ferzan; Yilmazer, Yasemin
Lightweight and functional metallic materials are consistently favored and attract significant attention in the biomedical field. This study investigates the influence of ZrN and DLC coatings on Ti6Al4V scaffolds with varying porosities (40%, 50%, 60%) for biomedical applications. PVD-deposited coatings exhibited distinct growth mechanisms: High-resolution SEM-FIB analyses revealed columnar ZrN structures due to limited adatom mobility, while DLC formed conformal, amorphous layers via high-energy carbon species. Corrosion resistance decreased in 40% porous DLC and 60% porous ZrN-coated samples, likely due to coating defects and increased electrolyte access through open pores. ZrN coatings showed superior antibacterial activity and attributed to surface reactivity and potential ion release. In contrast, the uncoated 60% porous scaffolds demonstrated highest cell viability, suggesting that excessive coating on highly porous structures may hinder cell–material interactions. Furthermore, the cytotoxicity evaluations indicated that uncoated scaffolds exhibited the highest cell viability (77.51%) at 60% porosity after 48 hours, with ZrN coatings demonstrating better efficacy compared to DLC in the 50% and 60% porosity groups.
AtıfScopus3WoS3OpenAlex3İncele - MakaleYalnız künye2026Scopus SJRQ2Stratigraphy, mineralogy, paleodepositional environment, and diagenetic evolution of the Pülümür evaporites (Tunceli, Eastern Anatolia, Türkiye)
Us, Muhammed Sami
The gypsum member of the Balpayam Formation (GMoBF) in the Pülümür Kırmızıköprü Basin (PKB), Eastern Anatolia, records a complex evaporitic system shaped by episodic tectonism, volcanism, and fluctuating hydrological conditions. Stratigraphic logging, facies analysis, and systematic sampling from outcrops and quarries enabled a detailed assessment of the evaporite succession. Petrographic data reveal pervasive secondary gypsum textures, including porphyroblastic, alabastrine, laminated, brecciated, and satin-spar fabrics preserving relics of primary anhydrite and calcite. XRD and FIB-SEM-EDS analyses identify gypsum, anhydrite, celestine, dolomite, calcite, clay minerals, and minor siliciclastic, clarifying diagenetic pathways. Diagenesis initiated with early calcite and aragonite precipitation, followed by replacement by primary anhydrite and gypsum under elevated Mg2+/Ca2+ ratios and shallow burial. Later hydration, dehydration, and rehydration cycles produced secondary gypsum with distinctive microtextures and micro-hydration channels. The PKB reflects a dual depositional system: a shallow, low-energy, restricted lagoon dominated by massive-laminated gypsum, stromatolitic textures, and organic-rich layers, and a comparatively deeper open marine setting with laminated-banded gypsum and transported gypsum arenite-rudite facies. Chicken-wire gypsum and anhydrite nodules indicate synsedimentary to early diagenetic formation under hypersaline conditions. A schematic depositional model constrains the temporal and spatial evolution of diagenetic processes, highlighting the interaction among evaporite deposition, tectonic activity, and environmental fluctuations in the southern Neo-Tethys Ocean of Eastern Anatolia.
- MakaleAçık Erişim2026Scopus SJRQ1Evaluation of electrical properties of poly(NIPA-co-St) composites containing neodymium and yttrium
Cetinkaya, Ebru; Karaaslan Ayhan, Nagihan; Torgut, Gulben
In this study, firstly, to obtain neodymium (Nd) and yttrium (Y)-containing composite materials, poly(N-isopropylacrylamide-copolymer-styrene) (poly(NIPA-co-St)) copolymer was synthesized by free radical polymerization method using N-isopropylacrylamide (NIPA) and styrene (St) monomers. Secondly, new composite materials were obtained by adding neodymium and yttrium to this copolymer at different weight ratios (10% and 20%). Structural and morphological characterizations of poly(NIPA-co-St) copolymer, poly(NIPA-co-St)-10%Nd, poly(NIPA-co-St)-20%Nd, poly(NIPA-co-St)-10%Y and poly(NIPA-co-St)-20%Y composite materials were carried out. The electrical properties of the copolymer and composite materials were evaluated by considering the frequency dependence of the dielectric constant (έ), dielectric loss (ε″) and electrical conductivity (σac) properties. At 100 Hz, the έ, ε″, and σac values of the copolymer were 5.12, 0.05, and 2.29 × 10−10 S/cm, respectively. With the addition of 10% Nd, the έ, ε″, and σac values at 100 Hz were calculated as 6.57, 0.10, and 1.79 × 10−9 S/cm, respectively, while with the addition of 20% Nd, these values were calculated as 8.39, 0.15, and 4.78 × 10−8 S/cm at 100 Hz. With the addition of 10% Y, the έ, ε″, and σac values at 100 Hz were calculated as 6.56, 0.053, and 1.81 × 10−9 S/cm, respectively, while with the addition of 20% Y, these values were calculated as 8.57, 0.0058, and 3.70 × 10−8 S/cm at 100 Hz. It can be stated that as the amount of Nd and Y additives to the poly(NIPA-co-St) copolymer increases, the έ, ε″, and σac values increase, indicating an improvement in electrical properties with the addition of Nd and Y elements.
AtıfOpenAlex1İncele - MakaleAçık Erişim2026Scopus SJRQ2Structural and optical properties of Bi- and Sn-doped Sb2Se3 thin films prepared by thermal evaporation
Kök, Mediha; Öztürk, Yunus; Sait Kanca, M.
In this study, Sb2Se3-based semiconductor thin films, both pure Sb2Se3 and those doped with Bi and Sn, were produced using the thermal evaporation method. The structural, morphological, and optical properties of the obtained films were investigated using XRD, SEM, and UV–Vis spectroscopy. While films without annealing exhibited an amorphous structure, significant crystallization was observed after annealing at 350 °C, especially at high doping levels. SEM analyses showed significant changes in surface morphology and grain structure depending on the doping level. Optical measurements revealed that absorption increased and the band gap changed with increasing doping level. The band gap for the undoped Sb2Se3 thin film was found to be 1.54 eV. An increase due to the Burstein–Moss effect was observed at low additive ratios, while band narrowing was observed at high additive ratios. The results obtained indicate that Bi and Sn additives improve the optoelectronic properties of Sb2Se3 thin films and hold potential for photovoltaic applications.
- MakaleAçık Erişim2025Scopus SJRQ2PCL/chitosan composite films enhanced with Bi2O3 in nuclear shielding applications: Irradiation resistance, thermal and structural properties
Yılmaz, Demet; Pekdemir, Mustafa Ersin; Dik, Gamze; Selçuk Pekdemir, Sibel; Ulu, Ahmet; Taşgın, Yahya; Ateş, Burhan
In this work, irradiation resistance, thermal, and structural characteristics of Bi2O3-reinforced poly ε-caprolactone/chitosan composites for nuclear shielding applications were studied. PCL/CTS/Bi2O3 composite films were prepared by using different amounts of Bi2O3 (0.5%–4.0% (w/v)). The radiation shielding parameters of the synthesized composite films were both experimentally and theoretically measured at the high energy region. The equivalent dose rates of the prepared film samples were measured using a fast neutron source. Also, to determine the irradiation resistance, the samples were irradiated with Am-241 and Co-60 sources for 30 days. The MFP values at 80.99 keV changed by approximately 61% in samples PCL/CTS and PCL/CTS/4% Bi2O3. The results show that Bi2O3 content increases the gamma shielding abilities in PCL/CTS films. According to TGA results, the thermal stability of the polymer composite films is increased by the addition of Bi2O3 to the PCL/CTS blend film. The results show that PCL/CTS composite materials can be used as protective coating materials for nuclear shielding. Highlights: PCL/CTS/Bi2O3 composite films were prepared by the solvent casting method. The thermal stability of the composite films increased by increasing the Bi2O3 amount. Bi2O3 increased the LAC and MAC values of the composite films. PCL/CTS/Bi2O3 composite films have a neutron shielding effect.
AtıfScopus5WoS5İncele - MakaleAçık Erişim2026Scopus SJRQ1Freeze–Thaw Performance and Microstructural Stability of Alkali-Activated Slag Mortars Incorporating Mussel Shell Waste
Şahin Yön, Merve
This study investigates the use of mussel shells (MSs), a biogenic by-product of the food industry, as a partial replacement for ground granulated blast furnace slag (GBFS) in alkali-activated mortars. Given their high CaCO3 content, MSs represent a sustainable secondary raw material that reduces both waste disposal burden and reliance on natural resources, while offering a low-carbon alternative to conventional cement-based binders. Alkali-activated mussel shell/slag mortars (AAMSs) were produced with MS replacement ratios of 0%, 5%, 10%, 15%, and 20% by mass of GBFS. Sodium hydroxide (NaOH) and sodium silicate (Na2SiO3) were used as alkaline activators. Fresh specimens were cured at 60 °C for 48 h. The experimental program included workability, compressive and flexural strength, water absorption, porosity, density, capillarity, ultrasonic pulse velocity (UPV), and freeze–thaw (F-T) resistance tests. Increasing MS content slightly reduced flowability and mechanical strength, while increasing water absorption, porosity, and capillarity. The M0 series achieved the highest 28-day compressive strength (54.06 MPa), while M15 exhibited the highest flexural strength (5.23 MPa). Following F-T cycling, the 5% and 10% MS series demonstrated the best compressive strength (30 MPa). The 10% MS exhibits a relatively balanced overall performance, providing the best balance between mechanical performance, F-T resistance, and microstructural stability, as confirmed by scanning electron microscopy (SEM)/energy-dispersive X-ray spectroscopy (EDS) analyses showing elevated Ca/Si ratios and the formation of Ca-rich crystalline phases.
- MakaleYalnız künye2026Scopus SJRQ1Determination of microplastic contamination and phthalate ester migration in canned and frozen packaged seafood: A probabilistic human health risk assessment via Monte Carlo simulation
Macit, Arife; Köktürk, Mine; Serdar, Osman; Alak, Gonca
This research was designed to identify the levels of microplastics (MP) and phthalate esters (PAE) in canned and frozen packaged fish and to assess the human health risks associated with these pollutants. Analyses were carried out on a total of 25 sample groups, including 10 different canned tuna samples, 9 different packaged seafood products, and 6 different packaging materials. Microplastics were characterized and polymer identification was performed using μ-Raman and ATR-FTIR spectroscopy, while PAEs were determined by GC–MS/MS. The obtained data were used to calculate estimated daily intake (EDI), hazard index (HI), hazard quotient (HQ), and cancer risk (CR), and uncertainty was assessed using Monte Carlo simulation. The findings revealed that both microplastic and phthalate exposure were higher in the frozen fish group than in canned products. The highest MP concentrations were recorded in packaged Whiting B (0.73 ± 0.25 items/g) and oil-added canned tuna (0.57 ± 0.15 items/g). Regarding PAEs, while DEHP and DBP were generally prominent, significant peak concentrations of BBP and DNOP were also identified, reaching 1.91 ± 0.01 ppm for BBP in canned tuna with sunflower oil and 1.84 ± 0.01 ppm in packaged whiting. Furthermore, higher exposure was observed in males for most PAEs. HQ and HI values were below 1 (maximum HI: 1.57 × 10−2 for males consuming frozen seafood), while CR values remained within an acceptable range (4.74 × 10−7 to 3.49 × 10−6). In conclusion, health risks related to processed fish consumption appear generally low; however, processing and packaging may contribute to contamination and warrant further investigation.
- MakaleAçık Erişim2025Scopus SJRQ2Species classification of microalgae using a CNN-based deep learning approach under optimal cultivation conditions
Simsek, Gokce Kendirlioglu; Ertargin, Merve; Pezzolesi, Laura; Pistocchi, Rossella; Yildirim, Ozal; Cetin, A. Kadri
Microalgae possess significant potential in a wide range of applications due to their valuable bioactive compounds. They are utilized in biofuel production to reduce dependence on fossil fuels, in wastewater treatment for the biological removal of heavy metals and pollutants, in carbon capture for mitigating climate change, and in the pharmaceutical and nutraceutical industries as supplements. As their applications expand, the accurate and efficient identification of microalgal species becomes increasingly important. Traditional classification methods are time-consuming and rely heavily on expert knowledge. The main aim of this study is to develop a reliable, fast, and expert-independent deep learning-based approach for the classification of microalgae species using microscopic images. In this context, deep learning techniques, specifically convolutional neural network (CNN)-based models were employed to classify microalgal species. Four widely used pre-trained CNN architectures (ResNet152, DenseNet201, MobileNetV2, and EfficientNetB0), along with a custom-designed CNN, were implemented. The models were trained and tested on a labeled dataset consisting of microscopic images of Chlorella vulgaris, Scenedesmus acutus, and Haematococcus pluvialis. The classification models achieved accuracy rates ranging from 96.87 % (Custom CNN) to 100 % (DenseNet201), demonstrating the potential of CNN-based approaches in automating and improving microalgae species identification.
AtıfScopus5WoS5OpenAlex5İncele - MakaleYalnız künye2026Scopus SJRQ2Exploring Nuclear Radiation Shielding Capabilities of High-Entropy Carbides: A Study on Composition and Effectiveness
Yilmaz Alan, Hatice; Guler, Omer; Yilmaz, Ayberk; Susam, Lidya Amon; Kavaz, Esra; Kilic, Gokhan; Ilik, Erkan; Oktik, Sener; Akkus, Baki; ALMisned, Ghada
High-entropy carbides (HECs) are emerging as promising materials for shielding against gamma-ray and neutron radiation due to their unique structural and compositional properties. This study systematically evaluates the shielding capabilities of 12 carbide-reinforced high-entropy alloys (HEAs) composed of elements such as hafnium, niobium, titanium, zirconium, tungsten, tantalum, vanadium, and molybdenum. Various gamma-ray and neutron shielding parameters, including attenuation coefficients, shielding thicknesses, and neutron removal cross sections, were calculated using the Phy-X/PSD software. The findings reveal a strong correlation between material density and shielding efficiency, with the highest density samples, particularly (Zr0.2Hf0.2Ta0.2Mo0.2W0.2)C and (Ti0.2Hf0.2Nb0.2Ta0.2W0.2)C, demonstrating superior gamma-ray attenuation. Additionally, neutron shielding performance was maximized in compositions containing high concentrations of heavy elements, with (Ti0.2V0.2Nb0.2Ta0.2W0.2)C exhibiting the most effective neutron absorption properties. The interactions of photons and charged particles with these materials were further examined through mass stopping power and projected range calculations for alpha particles, protons, and electrons. It can be concluded that HEC-based alloys, due to their high density, optimized composition, and superior radiation attenuation properties, could be strong candidates for advanced shielding applications in nuclear and aerospace environments.
AtıfScopus2OpenAlex2İncele - MakaleAçık Erişim2026Scopus SJRQ2Green Chemistry Meets Advanced Materials: Synthesis and Adsorption Performance of Ti3CNTx MXenes for Basic Red 46 Dye Removal
Aydın, Ekrem; Çelik, Aytekin; Köse, Yusuf; Hasar, Halil
In this study, Ti₃CNTₓ MXene nanosheets were synthesized from Ti₃AlCNTₓ MAX phase via two selective Al-etching routes: (i) direct hydrofluoric acid (HF) treatment and (ii) in-situ HF generation using a LiF + HCl mixture. Both approaches were systematically compared to evaluate their effects on structural integrity, surface chemistry, and adsorption performance toward the cationic dye Basic Red 46 (BR 46). Comprehensive physicochemical characterizations—including SEM–EDX, XRD, XPS, Raman spectroscopy, AFM, contact angle analysis, and TGA—confirmed successful Al removal and MXene formation for both methods, with notable differences in surface terminations and layer morphology. Batch adsorption experiments were conducted across a wide range of pH values (2–11), temperatures (25–60 °C), contact times (0–90 min), adsorbent dosages (0.05–0.40 g), and initial dye concentrations (10–50 mg/L). The HF-etched Ti₃CNTₓ exhibited rapid adsorption, achieving 99.6% removal at pH 2 within 20 min, whereas the LiF + HCl-etched sample demonstrated superior performance at moderate-to-alkaline pH and maintained high efficiency at lower dosages. Langmuir isotherm fitting revealed maximum adsorption capacities of 19.24 mg/g (HF route) and 28.01 mg/g (LiF + HCl route), supporting monolayer adsorption on homogeneous sites. Temperature-dependent studies further indicated an endothermic and spontaneous adsorption mechanism. Overall, the LiF + HCl route offers a greener and safer alternative to conventional HF etching while delivering competitive adsorption performance, improved structural stability, and faster equilibrium. These findings highlight the potential of sustainably synthesized Ti₃CNTₓ MXenes as high-performance adsorbents for dye-laden industrial wastewater treatment.
AtıfScopus2WoS2OpenAlex1İncele - MakaleAçık Erişim2026Scopus SJRQ1“A combined experimental numerical statistical framework to characterize fracture behavior of asphalt mixtures”
Atar, Muhammed; Ince, Ragip; Bakhshizadeh, Majid; Pirmohammad, Sadjad; Furtana Yalcin, Beyza; Yilmaz, Mehmet
This study investigates the fracture and viscoelastic behavior of asphalt mixtures through a combined experimental, numerical, and statistical approach. Semi Circular Bend (SCB) tests were performed on specimens with notch lengths of 10, 20, and 30 mm at two temperature levels (0 °C and room temperature) to determine fracture toughness (KIc), fracture energy, and stiffness parameters. The Extended Finite Element Method (XFEM) was employed to simulate crack initiation and propagation, providing a close match with experimental SCB results under various thermal and geometric conditions. To further interpret the effects of temperature and crack geometry, the Response Surface Methodology (RSM) was applied to the experimental data, enabling the identification of key interaction effects and optimization of fracture parameters. The results demonstrated that decreasing temperature and increasing notch length notably reduced fracture resistance, while XFEM accurately represented the nonlinear crack propagation observed in laboratory testing. Moreover, RSM provided predictive equations that were in strong agreement with XFEM outcomes. The proposed integrated SCB-XFEM-RSM framework presents an efficient and reliable methodology for evaluating and optimizing the fracture performance of asphalt mixtures, offering valuable insights for the design of durable and sustainable pavement systems under diverse environmental conditions.
AtıfScopus3OpenAlex3İncele - Kitap BölümüYalnız künye2026THE “OTHER” KARAGÖZ: The Kurdish Qeregoz
Çelik, Duygu
The traditional Ottoman shadow play Karagöz and Hacivat was broadcast in Kurdish on a Turkish state channel broadcasting in 2012. In this chapter, the author poses the question: are these Kurdish scenarios mere translations of the Turkish form, or did Qeregoz develop into a localized form of its own? Ultimately, the author contends that these plays in Kurdish represent a new staging style of the iconic form, and furthermore, the generous depiction of Kurdish life in Qeregoz on television had the effect of troubling a monolithic sense of “Turkishness.”
- MakaleYalnız künye2026Scopus SJRQ3Sensitive Electrochemical Analysis of Gentamicin Sulfate in Eye Solution
Ekşi, Osman; İpek, Yeliz; Koçak, Berna
In this study, for the first time, chromium (III) oxide-glutardialdehyde modified boron-doped diamond electrode (Cr2O3-GA2/BDDE) was used as a sensor for the electrochemical analysis of gentamicin sulfate. The Cr2O3-GA2 suspension used in electrode modification was physically coated on the BDD electrode by a simple drop-casting method. Characterization of Cr2O3-GA2 used in the modification was made by scanning electron microscopy, energy-dispersive spectroscopy (SEM-EDS), and the electrochemical method. The behavior of gentamicin sulfate on Cr2O3-GA2/BDDE was studied by cyclic voltammetry (CV), and its electrochemical analysis was done by differential pulse voltammetry (DPV). Electrochemical analysis of gentamicin sulfate on Cr2O3-GA2/BDDE was carried out in a pH 9 Britton–Robinson (BR) buffer by the DPV method. The linear working range of gentamicin sulfate on Cr2O3-GA2/BDDE was calculated as 5.96 × 10−6−6.54 × 10−5mol L−1, and the correlation coefficient was calculated as 0.997. The limit of detection (LOD) was found to be 2.84 × 10−6. mol L−1. Additionally, Genta, a 3% eye/ear drop solution, was preferred to determine the applicability of gentamicin sulfate in a commercial formulation. As a result, it was shown that the method developed on Cr2O3-GA2/BDDE for the determination of gentamicin sulfate can be applied to commercial drugs.
- MakaleYalnız künye2025Scopus SJRQ1Identification and source provenance of jadeite-bearing jade axes from Ulucak Höyük, Western Anatolia
Sayit, Kaan; Çevik, Özlem; Aktağ, Alican; Erdoğu, Burçin; Bamyacı, Onur; Vuruşkan, Osman; Sivil, Coşkun
The jades from Ulucak Höyük (İzmir, Turkey) are green-colored in hand specimen, and combined petrographic, XRD, and whole-rock analyses indicate that they mainly comprise jadeitic clinopyroxene, characterizing them as jadeite-bearing jades. Primitive mantle (PM)-normalized multi-element patterns reveal two distinct chemical groups. Both groups display depletion in Th and U; however, Group 1 shows a narrower elemental range and marked positive Pb anomaly. The second group, on the other hand, displays a wide elemental range in most elements and strong negative anomalies in Zr and Hf ([Nd/Zr]PM = 1.6–4.2; [Sm/Hf]PM = 1.8–3.5). Regarding REE systematics, both groups are characterized by weak positive slopes ([La/Yb]Ch = 1.7–5.3). However, whereas Group 1 shows coherent LREE-enriched trends, Group 2 displays flat- to LREE-enriched patterns with a wide range in Eu. When the geochemical features of Ulucak jades are compared with the high-pressure (HP) metamorphic rocks from Turkey and Greece, the similar multi-element patterns of Syros eclogites (Greece) to Group 2 Ulucak jades make Syros a possible source area for the Ulucak artefacts. On the other hand, the geochemical resemblance of the Sifnos jadeite-bearing gneisses to Group 1 Ulucak jades may raise the possibility of this island being another source for the Ulucak jades.
- MakaleAçık Erişim2026Scopus SJRQ1Forked hybrid architecture combining 1D-CNN and quantum convolutional networks for EEG signal classification
Esmeray, Furkan; Gülten, Arif
Detecting epileptic seizures from electroencephalogram (EEG) signals presents a significant challenge due to the nonlinear and non-stationary nature of brain activity. In this study, we propose a hybrid classification framework that integrates quantum-assisted and classical deep learning techniques to enhance detection accuracy and model interpretability. First, discrete wavelet transform (DWT) is applied to extract multiscale time–frequency features from raw EEG signals. Subsequently, three comparative models are developed: a conventional 1D-CNN model, an IQCNN model incorporating a parametric quantum circuit, and a novel Forked Enhanced Model that processes EEG features simultaneously through both 1D-CNN and IQCNN branches and combines them in a fully connected layer. The proposed hybrid model leverages the expressive power of quantum entanglement while preserving the robustness of classical deep learning. Evaluations using 5-fold stratified cross-validation on a real EEG dataset show that the forked architecture outperforms both classical CNNs and quantum-only based models in terms of accuracy, F1 score, precision, recall, number of incorrectly classified subjects and AUC. In this study, the best result was obtained with the Denoise IQCNNNet hybrid model. The accuracy of this model is 97.25%, precision 92.74%, recall 93.66%, F-1 score 93.15%, AUC 99.54%, number of incorrectly classified subjects are 57. This study demonstrates the feasibility and potential of hybrid quantum-classical networks in biomedical signal processing and provides a foundation for real-time clinical seizure monitoring systems.
- EditoryalAçık Erişim2026Scopus SJRQ1Recirculating Foundational Problems: Four Decades of Educational Computing in the JECR Archive (1987–2024)
Aslan, Alper; Akti Aslan, Seda; Turgut, Yiğit Emrah; Allison, Jordan; Özyurt, Özcan
This editorial presents a structured synthesis of the thematic development of the Journal of Educational Computing Research (JECR) from 1987 to 2024, drawing on a computational analysis of 1,597 articles. Applying Latent Dirichlet Allocation (LDA), the analysis identifies thirteen thematic structures that reveal both the enduring commitments and the emerging orientations of the journal across nearly four decades. Themes such as problem-solving through programming and self-efficacy in programming education have constituted persistent research agendas since the journal’s earliest volumes, while computational thinking and game-based learning have gained substantial momentum since 2015. These patterns suggest that JECR’s intellectual identity is best understood not as a sequence of discrete topical shifts, but as a sustained process in which a bounded set of foundational problems is repeatedly re-articulated under changing technological and epistemic conditions. The editorial situates this trajectory in relation to contemporary developments in artificial intelligence and educational technology, arguing that the journal’s historical archive offers an indispensable conceptual framework for interpreting present-day transformations.
AtıfScopus1OpenAlex1İncele - MakaleAçık Erişim2026Scopus SJRQ4Impact of Basalt Powder on the Physical, Fresh, Hardened and Microstructural Characteristics of Granulated Blast Furnace Slag-Based Alkali-Activated Mortars
Yön, Merve Şahin; Cemalgil, Selim
In this study, the workability, mechanical and physical aspects of alkali-activated mortar (AAM) containing basalt powder (BP) and granulated blast furnace slag (GBFS) were investigated. For the experimental study, alkali-activated mortars (AAM) containing BP at 8%, 16%, 24%, 32% and 40% substitution rates for GBFS were developed. Mortars were synthesized with a sodium silicate/sodium hydroxide ratio of 3.0 for the binder materials and a 0.45 alkali activator-to-binder ratio. The flow diameters of the fresh mortars prepared using 40x40x160 mm molds were determined according to the European Federation of Experts in Construction Chemicals and Concrete Systems (EFNARC) standard. The fresh AAMs were wrapped in stretch film to prevent evaporation and then kept in an oven at 60°C for 48 hours. The cured samples were evaluated for their mechanical strengths at 3 and 28 days, freeze-thaw effects after 33 and 100 cycles, and microstructures after 100 cycles. According to the results, using 40% BP instead of GBFS caused a decrease of approximately 15.08% in 28-day compressive strength compared to the reference sample (100% GBFS). G100 showed a minimum porosity of 15.81% and a water absorption rate of approximately 7.3%. The G60B40 mixture had the highest sorptivity capacity with 5.29x10-3 cm/s0.5, while the G100 mixture showed the lowest capacity with 3.88x10-3 cm/s0.5. After 100 freeze-thaw cycles, the G60B40 sample had the largest strength loss of 61.61%, while the G100 sample showed the lowest strength loss of 9.89%.
AtıfScopus1
İncele - MakaleYalnız künye2025Scopus SJRQ3Eco-Friendly and Practical Electrochemical Determination of Lactic Acid in Milk Using Boron Doped Diamond Electrode
İpek, Yeliz.; Koçak, Berna; Keçeci, Ali
In this study, an economical, environmentally friendly, sensitive, selective, and rapid voltammetric quantitative analysis method was developed using a boron doped diamond electrode to determine lactic acid (LA). Two linear working ranges were determined for LA determination in phosphate buffer solution (PBS, pH of 2). The first linear working range (LR1) was between concentrations of 1.5 × 10−6–8 × 10−6 mol· L−1, with a detection limit of 1.3 × 10−6 mol·L−1, and the limit of quantification (LOQ) was found to be 4.4 µmol· L−1. The second linear working range (LR2) was determined in the concentration range of 8.0–89.2 µmol·L−1. LOD was calculated as 15.8 µmol·L−1, and the LOQ value was calculated as 52.6 µmol·L−1 in the LR2. Intraday repeatability of the BDD electrode for LA determination was (RSD) 6.8% in LR1 and 11.8% in LR2. The interday repeatabilities of the BDD electrode in LR1 and LR2 were calculated as 7.7% and 4.7%, respectively. The developed electrochemical sensor was successfully applied for the determination of LA in milk sample. The sensor exhibited a short response time of about 10 s in PBS at pH 2. The recovery values of LA in PBS and milk sample were 97.3% and 96.1%, respectively.
AtıfScopus2WoS2OpenAlex2İncele
