Sürdürülebilir Kalkınma Amaçları
Yazarlar
Yayınlar
- MakaleYalnız künye2021Scopus SJRQ1Experimental design approach for ultra-fast nickel removal by novel bio-nanocomposite material
Ince, Olcay K.; Aydogdu, Burcu; Alp, Hevidar; Ince, Muharrem
In the present study, novel chitosan coated magnetic magnetite (Fe3O4) nanoparticles were successfully biosynthesized from mushroom, Agaricus campestris, extract. The obtained bio-nanocomposite material was used to investigate ultra-fast and highly efficient for removal of Ni2+ ions in a fixed-bed column. Chitosan was treated as polyelectrolyte complex with Fe3O4 nanoparticles and a Fungal Bio-Nanocomposite Material (FBNM) was derived. The FBNM was characterized by using X-Ray Diffractometer (XRD), Scanning Electron Microscopy-Energy Dispersive X-Ray Spectroscopy (SEM-EDS), Fourier Transform Infrared spectra (FTIR) and Thermogravimetric Analysis (TGA) techniques and under varied experimental conditions. The influence of some important operating conditions including pH, flow rate and initial Ni2+ concentration on the uptake of Ni2+ solution was also optimized using a synthetic water sample. A Central Composite Design (CCD) combined with Response Surface Modeling (RSM) was carried out to maximize Ni2+ removal using FBNM for adsorption process. A regression model was derived using CCD to predict the responses and analysis of variance (ANOVA) and lack of fit test was used to check model adequacy. It was observed that the quadratic model, which was controlled and proposed, was originated from experimental design data. The FBNM maximum adsorption capacity was determined as 59.8 mg g−1. Finally, developed method was applied to soft drinks to determine Ni2+ levels. Reusability of FBNM was tested, and the adsorption and desorption capacities were not affected after eight cycles. The paper suggests that the FBNM is a promising recyclable nanoadsorbent for the removal of Ni2+ from various soft drinks.
AtıfScopus11WoS11OpenAlex7
İncele - MakaleAçık Erişim2021Scopus SJRQ3A novel macrofungus for the biosorption of hazardous dye and its reuse potential: Experimental design approach using response surface methodology
Ince, Olcay Kaplan; Alp, Hevidar; Ince, Muharrem; Onal, Ali
In the present study, a novel biosorbent, namely Agaricus campestris, was used for the removal of Methylene Blue (MB) from an aqueous medium. The biosorbent was characterized using fourier-transform infrared spectrometer spectra, scanning electron microscopy-energy dispersive X-ray, and thermogravimetric analysis. The influence of important process parameters including pH (4–7), temperature (25°C–35°C), contact time (15–25 min), and biosorbent amount (40–80 mg) on the uptake of MB solution were also optimized, which significantly affected the removal efficiency of MB. A central composite design (CCD) combined with response surface modeling (RSM) was carried out to maximize MB removal by A. campestris for the adsorption process. A regression model was derived using RSM to predict the responses and analysis of variance (ANOVA), and to check model adequacy lack of fit test was used. The A. campestris adsorption capacity was determined as 24.2 mg g–1. The ANOVA showed a high coefficient of determination (R2 = 0.9987). This study clearly revealed that RSM was one of the most effective and appropriate method for the optimization of operating conditions. The possibility of reusing A. campestris was also investigated and, as a result, it was found quite possible and showed high performance in the recovery of MB.
AtıfScopus2WoS1OpenAlex2İncele - MakaleAçık Erişim2020Scopus SJRQ3Biosorptive removal of eriochrome black-T using agaricus campestris: Parameters optimization with response surface methodology
Alp, Hevidar; Ince, Muharrem; Ince, Olcay Kaplan; Onal, Ali
In this study, Eriochrome Black T (EBT) removal from aqueous media by Agaricus campestris (AC) which is an eco-friendly biosorbent was investigated using a central composite design (CCD) combined with response surface methodology. The CCD was chosen as the statistical prediction method to reduce the number of experiments which, in turn, will directly save time and chemicals. To opti-mize the process, various experimental independent variables such as the pH of the solution, contact time, adsorbent dosage and temperature were selected. The optimal experimental conditions were obtained as 6.5, 30°C, 20 min and 20 mg, for solution pH, temperature, contact time and adsorbent dosage, respectively. Under these optimized conditions, maximum EBT (100 mg L–1 initial concentra-tion) removal efficiency was calculated as 64.2 mg g–1. The independent variables and their interaction significance were checked using analysis of variance and it was found that the EBT biosorption on AC was highly significant (p < 0.001). The results were justified by the relatively high correlation coefficients (R2 = 0.9967) of the statistical prediction. The EBT biosorption was confirmed by fourier transform infrared spectroscopy (FTIR) analysis monitoring the functional groups during EBT biosorption on AC. This was the first report on the parameter optimization of EBT biosorp-tion using AC in an experimental design. The used biosorbent was characterized by FTIR, scanning electron microscope coupled with energy dispersive spectrometer and thermogravimetric analysis. The proposed biosorption process efficiently removed EBT, present in various aqueous mediums and can be used in industrial processes.
AtıfScopus17WoS12İncele